The DataMan 470 backside barcode reading system offers the following benefits: ▪ Real-time decoding ▪ Achieve a read rate of 99.9%. ▪ Easy to install and maintain ▪ It is not susceptible to the vibration of the package ...

Cognex Corporation (NASDAQ: CGNX), one of the global leaders in industrial machine vision, has released the DataMan? 580 Fixed Barcode Reader. Designed for Cognex's modular vision channels, the DataMan 580 enables faster operations and improved traceability ...

interface and communication method settings. How to set it up: 1. Interface selection There are a variety of options for referring to the interface of the scanner, such as RS232, PC keyboard, etc. Some scanners must be set to RS232, if the parameters are messed up and change to keyboard mode, then set it anyway ...

1. Scanning may be due to unclear barcode, wrinkles, reflections, angles and other problems of the product itself. 2. The connection of the barcode scanner does not meet the transmission specifications. 3. The interface of the barcode scanner or computer is loose. 4. The Bluetooth scanner cannot be connected to the computer normally. ...

Faults that may be encountered with the use of a barcode scanner 1. After the code scanner is successfully connected, the LED flashes continuously, and there is no sound, so it cannot be scanned. Possible causes: It is usually caused by poor IC contact. Solution: In this case, please contact the dealer or manufacturer.

1. Problem description: LED is not on, no beep, no laser Possible causes: The power supply of the scanner is not on, the scanner is not powered or the data cable interface is loose, and the contact is poor Solution: Check the cable of the scanner to make sure that the power supply of the computer is normal, and the data cable is reconnected to the scanner.

1. The zebra scanner is set when the barcode scanner is scanning, and the beep is normal but there is no data transmission This problem may be caused by the incorrect scanning settings of the scanner, resulting in no data transmission of the scanner, and another reason may be that the transmitted cable is faulty, ...

1. Check the manual of the scanner, find the automatic enter setting diagram, scan the first barcode to open the setting code, and then scan the barcode below to allow the end suffix to be added. 2. Re-scan the barcode that allows you to add a terminator suffix. 3. Set the suffix of the ending character, and ...

1. Install the driver. Connect one end of the data cable with a crystal tip to the base, and the other end with the corresponding interface of the computer, the computer will automatically install a driver, and wait for the automatic installation to be completed. 2. Pairing. Use the wireless scanner to scan the ...

There are several possibilities: 1. Failed to connect with the computer correctly. (especially the data cable of the PS2 interface) 2. Data cable failure 3. Poor interface contact 4. The interface of the scanner is set incorrectly. (Is it PS2 or USB interface data cable, to and scanner parameters ...

1. The connection of the code scanner does not meet the transmission specifications; 2. The interface of the barcode scanner or computer is loose; 3. The Bluetooth scanner cannot be connected to the computer normally.

1. If the scanner is not connected to the computer, it may be caused by a loose USB interface or an aging line, you can try to replace the USB cable or replace the interface. 2. The barcode scanner is set incorrectly, it may be that the settings of the barcode scanner do not match the settings of the computer, you can check the scanner ...

Fault 1: The scanner can't scan the barcode Solution: In this case, you must first understand whether you can scan the barcode but not upload it, or the laser but not scan the barcode. You can scan the barcode but do not upload to the computer is that the computer and the scanner are not connected well, if it is wired to check ...

1. Cognex power cord Load the power supply into the chassis 2. In the power cord, find the 24-pin cable for the motherboard. 3. In the motherboard, find the 24-pin power connector, insert the power cable into the motherboard, and pay attention to the position of the bayonet of the power cable. 4. In the power cord, find the power supply for the motherboard.

1. Insert the scanner first (until you hear the prompt sound that the barcode scanner has been successfully installed). 2. SECONDLY, OPEN EXCEL (OR ANY SOFTWARE THAT CAN INPUT TEXT). 3. Scan the barcode again (set the scanning mode of the barcode gun as needed, such as carriage entry after scanning, line wrap...)

1. First of all, Cognex's barcode scanner needs to go to the official website to download Dataman's special configuration software 2. The following configurations are mainly made in the configuration software: focal length, communication settings (including serial port baud rate, etc.), data format of scanning code, trigger mode, etc. If you don't, ...

1. Check whether the power extension cord of the camera is too long and the output voltage and current of the adapter are insufficient: the power supply of the camera is insufficient, and the red light is always on, and it cannot be started and reset normally. Please make sure that the power supply voltage and current of the camera meet the requirements before trying. 2. If the camera is safe ...

Cognex Corporation (NASDAQ: CGNX), one of the global leaders in industrial machine vision, has announced the new In-Sight® 3800 vision system. Designed for high-speed production lines, the In-Sight 3800 offers an extensive library of vision tools, advanced imaging capabilities, and flexible software ...

Cognex Corporation (NASDAQ: CGNX), one of the global leaders in industrial machine vision, recently announced the new DataMan®282 fixed-mount barcode reader with Cognex's high-power integrated flare-shaped light source (HPIT) and dome illumination accessory options. These...

Hardware failure 1: After reading a barcode, the reader crashes Exclusion Tests: 1) Because of the protection function of the barcode reader, if the read barcode data is transmitted incorrectly, it will automatically enter the protection state, thereby preventing data loss. If you read the data that has not been successfully transmitted...

1. Flip through the detection program and prompt that the camera cannot be found Investigation method: (1) Check whether the power supply of the camera is connected and whether the camera network cable is damaged. (2) Check the NIC driver and camera driver. (3) Check the network card parameters, camera and computer IP. 2. The process of use ...