The first is that the pressure rises and the transmitter cannot convey. In this case, the first thing to do is to check the pressure connection for air leaks or blockages. If not, check the wiring method and power supply. If the power supply is normal, simply pressurize and see if the output changes, or if the sensor part outputs. As...

1. Flange fixed installation Flange mounting is to connect the pressure sensor to the flange and fix the flange to the measured object. The advantage of this installation method is that it is simple in structure, easy to install and disassemble, and suitable for occasions where frequent sensor replacement is required. But...

Cleaner: Clean the surface of the Banner sensor with a special cleaner to remove dirt and dust. Do not use any acidic or alkaline cleaners to avoid damaging the sensor surface. It is recommended to use anhydrous alcohol or deionized water for cleaning. Lube: Some Banner sensors require ...

1. It is necessary to prevent the sensor from engaging with corrosive gases, preventing it from corroding and affecting the effectiveness of measurement. 2. Assuming that the measurement is a high-temperature medium, it is necessary to see whether the temperature is within the appropriate temperature scale of the sensor.

First, the test method of pressure sensor The test on pressure sensors mainly includes the following aspects: Resistance test Output signal test Overload test 1. Resistance test The test machines are as follows: power supply, multimeter, ammeter, ...

First, the reason for the alarm code of the pressure sensor There are generally a variety of reasons for the alarm code of a pressure sensor, among which the following conditions are the following: 1. The sensor circuit is short-circuited or broken due to damage or aging of the sensor sensing element, which causes the machine code to send an alarm signal. ...

1. Acquisition, processing and transmission of detection signals; 2. Signal filtering technology is used to remove noise; 3. Use relevant technologies for signal analysis and data processing of the results; 4. Choose the most suitable amplification technology to improve the signal strength according to the actual situation; ...

1. The reason for the total alarm of the sensor The total sensor alarm is when the sensor's alarm indicator is always on, but the sensor is not actually catching the outlier. This can happen for a variety of reasons, but here are some of the most common ones: 1. Sensor device ...

1. First, power off the sensor and remove it. 2. Use a clean cotton swab dipped in an appropriate amount of anhydrous alcohol and quietly scrub the reception window. Be careful not to use water or organic solvents to avoid damaging the sensor. 3. After scrubbing, use a clean cotton swab to accept ...

The photoelectric head of a photoelectric sensor is a precision device, and misalignment can seriously affect the measurement results. This usually happens when external forces interfere with it, such as when the sensor position is shifted due to excessive force during cable construction. At this point, the position of the photohead needs to be readjusted. How to adjust: ...

1. Understand the basic wiring principle of photoelectric switch sensors. Photoswitching sensors typically have three pins: the power pin (V+), the power ground pin (V-), and the output pin (OUT). The power pin is used to connect to the positive terminal of the power supply, the ground pin of the power supply is used to connect to the negative terminal of the power supply, and the output pin ...

1. Temperature measurement: Fiber optic sensors can measure temperature by measuring the thermal expansion or thermal conductivity of optical fibers. It can be applied to industrial process control, power system monitoring, fire early warning and other fields. 2. Pressure measurement: Fiber optic sensors can measure the bending of optical fibers by ...

1. Determine the installation location. Like injection molding machines, hydraulic presses, etc., are generally installed on the front 2 sides, and some non-standard equipment should be determined according to the actual situation to determine the installation position, to achieve the role of protection, without hindering the normal work. 2. Punching. Determine the installation location ...

1. The brown line VCC of the transmitter is connected to the brown line VCC of the receiver, and then the power supply is +24DC. 2. The transmitter black wire GND is connected to the receiver black wire GND, and then connected to the power supply negative OV. 3. The transmitter gray line CP is connected to the receiver gray line CP. 4. Receiver Blue ...