Product introduction: P+F sensor output interface terminal KCD2-E2L Sensor output interface terminal with conductor disconnection monitoring
Indicator/Operation Method:
Yellow LED: Switch output Wire disconnects: LED off, output locked
Electrical Specifications:
Operating voltage: 10 ... 30 V DC
Ripple: ≤ 10 %
Operating current: approx. 22 mA
Input:
Connection: Terminals 1+, 2-
Connectable sensor type: NAMUR
Pulse length/interval : ≥ 0.5 ms / ≥ 0.5 ms
Short-circuit current: approx. 8 mA
Sensor power supply: 8 V DC, maximum voltage 9 V DC Ω at minimum input impedance 562
Switching points: 1,2 ... 2,1 mA hysteresis is about 0.2 mA
Line Fault Detection: Yes
Threshold: 1 kHz
Output:
Connection: Terminal 4+
Current: 200mA short circuit protection
Transistor: PNP
Signal level: UB-1.1V
Electromagnetic Compatibility:
Directive 2014/30/EU: EN61326-1:2013
Standards:
Protection level: EN60529: 2000
Immunity: EN61326-1:2013
Environmental conditions:
Ambient temperature: -25..70C (-13..158°FF)
Storage Temperature: -25..85C (-13..185F)
Connection: Self-opening device connection terminals, maximum core cross-sectional area 0.34... 2.5mm2
Mass: 60g
Size: 20x60x40 (unit: mm)
Our customer-centric service concept: the pursuit of a full range of services is a high-quality, high-standard service, the pursuit of every detail of the service process. It is impossible for interests to blossom into brilliant flowers from lies. Only by being professional and careful in every process, every action and every detail of the service can we meet or even exceed customer expectations and make customers satisfied and recognize us. Honest, professional, affordable, and fast, so you can rest assured. "Honest and professional service, affordable price, continuous improvement" is our service philosophy.
This article describes: P+F Sensor output interface terminal KCD2-E2L products, if you are interested in P+F/DoubleSensor output interface terminalIf you are interested, please also contact our customer service, we look forward to your call, and hope that our technology and service can bring you a better experience.
|
More on that
|
P+F/Diffuse Reflex Mode Sensor GLV18-8-200 /115/120
Product Description: Triangulation sensor with background suppression, miniature design with multiple mounting options, best-in-class background suppressor, accurate object detection, virtually independent of color, extended temperature range.
Our customer-centric service philosophy ...
|
|
P+F Inductive Sensor NBB20-U1-A2 20mm flush
Introduction: Smooth or threaded stainless steel housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indication; M8, M12 connector connection or terminal wiring; PVC, PUR or silicone cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR and AS ...
|
|
P+F/Capacitive sensor CCN15-30GS60-A0/A2 complementary output
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CBN15-F64-A2-0, 3M-V1
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CJ40-FP-A0-P1 has a voltage drop of ≤ 2.8 V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F Signal Conditioner S1SD-1AI-1C.H Resistance 50Ω
Introduction: The P+F signal conditioner SC series provides isolation in an extremely compact package and is optimized for the application requirements of the safe area. Connected via screw terminals, according to EN 60715:2001, mounted on a 35 mm DIN mounting rail.
...
|
|
P+F/Capacitive sensor CJ10-30GM-WS current: 5~200mA
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CJ4-12GK-N-10M with a rated voltage of 8V
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/UBE800-F77-SE2-V31 1 switch output PNP
Product Introduction: Thru-Beam Ultrasonic Barrier, Miniature Design, High Brightness LED, For Power-On and Switching Status, High Switching Frequency, Series: -F77, Housing Diameter: , Housing: Polycarbonate, Output Type: 1 Switching Output PNP, NO, Sensing Range: 0 ... 800 mm launcher ...
|
|
P+F/Capacitive sensor CBN15-F64-A2 15mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
P+F/Capacitive sensor CBN15-18GS75-E2 normally open PNP
Introduction:P+F The CBN15-18GS75-E2 capacitive sensor is usually measured by one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When there is an object moving towards the proximity switch, ...
|
|
P+F/Background Suppression Sensor RL31-8-H-800-RT/73C/136
Product Description: Triangulation Sensor, Standard Application Background Suppression, Large Housing Design, 800 mm Adjustable Detection Range, Red Light, Low Light, Push-Pull Output, M12 Plug, Cost-Optimized Series for Standard Tasks, Small Housing Large Construction, High Visibility Indicator, Low Target Color ...
|
|
P+F/Inductive sensor NBB20-L2-A2-V1 flush mounted
Introduction: Smooth or threaded stainless steel housing for inductive sensors; reverse polarity protection and short circuit protection; LED status indication; M8, M12 connector connection or terminal wiring; PVC, PUR or silicone cable outlet; 2-wire, 3-wire, 4-wire DC, AC, NAMUR and AS ...
|
|
P+F/Sensor NBN3-F31K2-E8-B43-S 2.5 mm
Introduction: P+F/Sensor NBN3-F31K2-E8-B43-S is mounted directly on a standard actuator, waterproof housing, suitable for outdoor use, temperature range -40 ... 167 °F (-40°C to 75°C), energized LED, LED indicating sensor and solenoid status switching, mating end ...
|
|
P+F/Tilt sensor INX360D-F99-I2E2-5M IP68/IP69K
Product Description: The new generation of the F99 inclination measurement sensor is ideal for industrial environments due to its simplicity, durability and compact housing. The F99 inclination measurement sensor offers a standardized 4 ... 20 mA analogue interface with a measuring range of 0 ... 360° between, no need for expensive total ...
|
|
P+F/M100/MV100-6090/102/115 through-beam photoelectric sensors
Product Introduction: Thru-beam sensor, miniature design, miniature sensor light forming slit, easy to use, very bright, high visible light point, full metal threaded mounting.
Our customer-centric service concept: the pursuit of a full range of services is a ...
|
|
P+F Capacitive sensor CCB10-30GS55-N1-V1
Introduction: Capacitive sensors can be used to detect targets in almost any material, including metal. These sensors are used in a wide range of applications for level and flow control, mainly liquids, particles and powders.
Give birth...
|
|
P+F/Inductive sensor NBB8-18GM50-E0-M 8mm
Summary: Inductive proximity sensors are the product of choice for most applications that require the precise and non-contact detection of metal objects in machinery or automation. As a pioneer and market leader in the field of sensors, we offer our customers innovative, high-quality inductors.
|
|
P+F/Through-beam photoelectric sensor OBE2000-R2-SE0 20 g
Description: The P+F/P+F/Through-beam photoelectric sensor OBE2000-R2-SE0 with its ultra-small housing design and 45° cable outlet provides maximum installation freedom, even in very space-constrained conditions.
Product Features ...
|
|
P+F capacitive sensor CJ10-30GK-WS housing diameter 30 mm
Introduction: The measurement of P+F/Capacitive sensors is usually one plate that makes up the capacitor, and the other plate is the housing of the switch. This housing is usually grounded or connected to the enclosure of the device during the measurement process. When an object moves towards a proximity switch, whether it is a conductor or not...
|
|
Contact
working hours
