Pneumatic valve fault location analysis - Wuzhong instrument

Pneumatic butterfly valves are usually composed of a combination of pneumatic actuators and valve bodies and some accessories after debugging. This article first introduces the precautions for the on-site application of pneumatic butterfly valves. 1. The control cabinet sends a signal that the valve does not move, and the pneumatic conditioning butterfly valve is in the device locator after on-site investigation.

The slag lock valve (bucket valve) is specially designed for the complex working conditions of coal gasification, and is a special hard seal ball valve that can adapt to high temperature, high pressure and high wear resistance working conditions. The slag locking valve is mainly used to solve the problem of coal slurry feeding in the gasification unit and the common problem of medium scaling in the valves used in the black water process pipeline.

Insist on the cleanliness of valves and actuators as much as possible. The valve is drained after the flow test. During storage and installation, it is important to avoid the ingress of contaminants. Assuming that there is a problem, check it according to the instructions. Do not use a crowbar or an excessively large ...

1. The sealing surface is uneven and cannot constitute a sealing line: 2. The connection between the valve stem and the closure is suspended, irregular or worn; 3. The valve stem is tortuous or the assembly is not correct, so that the closure is skewed or mismatched: Fourth, the sealing surface raw materials are not selected properly or not according to the working conditions.

1. Impurities are stuck on the sealing surface of the valve The valve is sometimes closed suddenly, it may be that there are impurities stuck between the sealing surface of the valve, at this time should not be forced to close, the valve should be opened slightly larger, and then try to close, try repeatedly, it can generally be eliminated, otherwise it should be checked again...

Cryogenic valves are mainly used in ethylene, liquefied natural gas units, air separation equipment, petrochemical tail gas separation equipment, liquid oxygen, liquid nitrogen, liquid argon, carbon dioxide cryogenic storage tanks and tankers, pressure swing adsorption oxygen production devices, etc., the main varieties are cryogenic ball valves, cryogenic globe valves, etc. ...

1. The valve position of the electric actuator is lost: 1) Battery power is lost When the incremental encoder is selected to measure the stroke, it is necessary for the fulfillment mechanism to have a battery as an auxiliary power supply, the AC power supply disappears, and the change of the valve position of the electric actuator can still be detected by the incremental encoder.

The commonly used medium for valve pressure testing is water, oil, air, steam, nitrogen, etc., and the pressure testing methods of various valves are as follows. (1) Globe valve and throttle valve For the strength test of globe valve and throttle valve, the assembled valve is usually placed in the pressure test frame, the valve disc is opened, and the medium is injected into the ...

Nowadays, the valve market is mixed, and illegal traders pretend to be innovative valves to be shoddy in order to make huge profits, which brings great safety risks to the installation project. Therefore, it is necessary to introduce to you the inspection of innovative valves. At present, the valve market dealers mainly exist in the valve counterfeiting ...

Now the valve market is mixed, and illegal traders pretend to be innovative valves to be shoddy in order to make huge profits, which brings great safety hazards to the device project. Therefore, it is necessary to introduce to us the inspection of innovative valves. Now the valve market dealers mainly exist in the valve counterfeiting ...

1. The safety valve should have the equipment to prevent the hammer from moving by itself and the guide frame to limit the lever from deviating, and the spring-type safety valve should have the equipment to raise the handle and prevent the adjustment screws from being twisted at will. 2. It should be installed straight in the pot merchant, the container ...

Two-position five-way solenoid valve is a pneumatic component commonly used in gas-electric automatic control system, its main use is to control the double-acting cylinder to complete the automatic switching of the air circuit, widely used in the pneumatic equipment of various industrial parts, to complete the automatic control and long-distance operation in the production process, it has the ability to ...

1. Torque maintenance refusal To measure the output torque of the electric actuator, there are mainly mechanical maintenance switches, motor current and voltage power measurement and calculation torque, and sensor-type maintenance devices: mechanical torque maintenance switches were used more before 2000 and were classified as a transitional product.

G2010 ball valve for long-distance pipeline is designed for the transportation of long-distance pipeline media, which is a typical long-distance pipeline ball valve, which is suitable for various oil, natural gas, city gas pipelines, and can also be used in the equipment of general chemical products. The valve is completely in line with the United States Petroleum Institute API in terms of performance...

The stem axis of the globe valve is perpendicular to the seat sealing face. The relatively short open or closed stroke of the valve stem and the very reliable blocking action make this valve very suitable for the blocking or adjustment of the medium and the economical application. ...

The process of shell experiments and seal experiments done by turbine fixed ball valves in some artificial environments is as follows. Double blocking and discharge function of turbine fixed ball valve: the turbine ball valve is fixed by using tension spring preload floating valve seat, when the valve is in two different states, fully open and fully closed, the fluid is ...

1. Introduction to gate valves Gate valve refers to the valve in which the opening and closing parts (rams) move in the straight direction of the medium (channel axis) to complete the opening and closing. Among the various types of valves, gate valves are the most widely used one. Gate valves are mainly used as shut-off medium in pipelines, i.e. ...

　　First, the effect of pipeline identification Why do you need to do pipeline identification? Intent: To facilitate the identification of substances in industrial pipelines, ensure safe production, and avoid misjudgment in operation and equipment maintenance. Carry out ...

A few days ago, in a large digital workshop of Wuzhong Instrument Co., Ltd., the operators were working carefully. Every day, tens of thousands of parts orders are sent from dozens of sales outlets across the country such as Guangzhou and Hainan, and nearly 200 pieces of equipment in the workshop are processed and produced. 　　Because of the working conditions ...

1. The signal valve pushed by the control box does not move. Under the condition that the positioner is installed, the pneumatically adjustable butterfly valve is equipped with a solenoid valve. The weak current of the solenoid valve affects the information output of the control box, and the valve cannot withstand the data signal and cannot work normally. ...