IDEC/Izumi HS1E-K Solenoid Safety Switch 3 Circuit Type HS9Z-A2

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

IDEC/Izumi Safety Interlock HS6B Subminiature Safety Interlock Switch HS6B-12B01 2NC 1NO Contact, 1m Cable 30x15x78mm enclosure One-piece cables reduce wiring time IP67 (IEC60529) waterproof sealing (contact sealing; The enclosure allows for drainage) Open directly ...

The resin-based actuator for HS5 series safety switches can be easily mounted to the hand-held enabling switch with the two screws included. By combining a resin-based actuator with an HS5 series safety switch fixed to a mechanical device, it is easy to maintain the hand ...

VD circuit, key detachable in all positions, key 501,3m cable Mechanical Specifications: Product Category Safety Interlocks Key removal location for all positions Environmental indicators Degree of protection IP65 Installation and installation specifications Cable length 3 meters Our customer-centric approach ...

It is equipped with a "operation head detachment detection function" that turns the main circuit (11-12) into the OFF state when the operating head falls off. It is the same size as the HS5B type (external dimensions, mounting dimensions), and is available as a 3-contact model with dual contacts + auxiliary contacts. Small size allows installation in confined places ...

IDEC/Izumi HS6B Subminiature HS6B-02B03 Safety Interlock Switch 2NC Contact, 3m Cable 30x15x78mm enclosure One-piece cables reduce wiring time IP67 (IEC60529) waterproof sealing (contact sealing; The enclosure allows for drainage) Direct door opening action: even if ...

The world's thinnest solenoid interlock switch is 15mm wide Flexible installation - reversible mounting and angled cables allow for four actuator insertion directions Energy saving - 24V DC/110 mA Three sides can be manually unlocked The LED indicator shows solenoid valve operation Standard 3m cable (available on request)

Compact 3-position enable switch with auxiliary contacts. Ergonomic OFF→ ON → OFF 3-position action for hazard avoidance. Between pressing OFF (position 3) → releasing OFF (position 1), the structure of the ON state is not formed. IEC60204-1（2005） ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

All M3.5 wiring screws are used to improve the connection line. The contact structure is 2 circuits with 1NC+1NC main circuit and 1NC auxiliary circuit, and it is possible to support dual main circuit + lock monitoring circuit. There is also a key with a portable key as standard for hostage control ...

With a clear feeling of pressure, the 3-position action can be reliably distinguished. By reducing the load on hand handling, the burden on the user during long-term use is reduced. Key features: 3-position action of OFF ⇒ ON ⇒ OFF for danger avoidance. Press OFF (position 3)⇒ Release OFF...

VD circuit, key detachable in all positions, key 502,3m cable Mechanical Specifications: Product Category Safety Interlocks Key removal location for all positions Environmental indicators Degree of protection IP65 Installation and installation specifications Cable length 3 meters Our customer-centric approach ...

The actuator is mounted on the guard, the safety switch is mounted on the mechanical body, and the mechanical locking guard is installed. When the inertial action of the machine stops, the electromagnetic coil excitation is unlocked by an electrical signal from the controller, etc., for greater safety. In the event of a power outage and maintenance, special tools can be used ...

The dimensions are 35×40×146mm. This is a backside lock release button type that can be used for emergency evacuation, etc. A back-locking release button unit that can be mounted on an aluminum frame is also available. 4. The independent circuit type and the safety circuit are dualized, so that the circuit variety is more complete. , which can cope with small loads ...

Small, lightweight, low-cost, high-performance safety switches. Key features: Small size: 30mm× 30mm×90mm, by changing the mounting direction of the top, the actuator can be inserted from 8 positions, so as to meet different installation needs. IP67 (IEC60529) contact ...

IDEC/Izumi Safety Interlock HS1T Heavy Duty Locking HS1T-VG44ZSM-G 4 contacts 2NC, 1NO and 1NC, spring lock, side wires 5000N locking force is the smallest in the industry Spring-loaded terminals prevent loose wires Energy saving 200mA solenoid consumption Electromagnetic locks and snap locks are available ...

Vertical operating unit with ø16 mounting holes for easy installation. 2-contact 3-position switch for small teach pendants. Key features: Ergonomic, 3-position action of OFF ⇒ ON ⇒ OFF for danger avoidance. Position 1 ⇒ 2, built-in snap-action switch with light ...

The actuator is mounted on the guard, the safety switch is mounted on the mechanical body, and the mechanical locking guard is installed. When the inertial action of the machine stops, the electromagnetic coil excitation is unlocked by an electrical signal from the controller, etc., for greater safety. In the event of a power outage and maintenance, special tools can be used ...

Small size: 30mm× 30mm×90mm, by changing the mounting direction of the top, the actuator can be inserted from 8 positions, so as to meet different installation needs. IP67 (IEC60529) protection structure is used for the contact parts. The NC contact has a direct disconnect operation structure. （IEC/EN60947 ...

All M3.5 wiring screws are used to improve the connection line. The contact structure is 2 circuits with 1NC+1NC main circuit and 1NC auxiliary circuit, and it is possible to support dual main circuit + lock monitoring circuit. There is also a key with a portable key as standard for hostage control ...