KEYENCE/KEYENCE Multi-Point Laser Sensor IX-1050

Sensor Controller Extension

KEYENCE/KEYENCE Multi-Point Laser Sensor IX-1050

specification

Main Units / Expansion Units		Extensions
display	The smallest display unit	10 µm*1
	Display range	± 999.99 to ±999 mm (4 sections optional)*1
tool	Scan mode	Height, Height Difference, MAX/MIN, Height Difference Calculation, Thickness Calculation, Height Area, Black & White Area, Position Correction
		(Maximum number of settings) Identification tool: 16 tools, Position correction tool: 1 tool*2
	Straight line mode	Height (AVE/MAX/MIN), Height difference (AVE/MAX/MIN), Height difference calculation, Thickness calculation, Position correction, Tilt correction
		(Maximum number of settings) Recognition tool: 16 tools, Position correction tool: 1 tool, Tilt correction: 1 tool*2
Other features	general	ZERO / Offset, In-Flight Threshold Change, 2-Point Calibration, Measurement Direction, Measurement with Position Correction NG, ZERO / Offset Memory, Shooting Mode (HDR), Additional Sensor Date Time
		Information, N.O./N.C. switching, I/O monitor, automatic brightness adjustment, illumination (ON/OFF), comprehensive judgment conditions, NPN/PNP switching, primary and secondary input at the same time, mutual interference prevention, password
	Scan mode	Measurement Range, Measurement Position (Small / Standard / Large), Measurement Mode, Measurement Interference Removal, Shooting Mode (High Gain),
		Tilt Correction (Optional Fixed, Real-Time Correction), Halo Reduction, Trigger Input (Internal/External), Trigger Interval, Trigger Delay, Trigger Error,
		Black and white bar chart function, datum area fixation, profile neutralization, rotation range
	Straight line mode	Average times, laser position adjustment, TIMING input, sensor probe tilt correction (fixed only), measurement ambient light cancellation, HOLD function, alarm setting, measurement method (average / maximum / minimum)
input	input	Passive contact input / voltage input can be switched
		Passive contact input: ON voltage 2 V or less, OFF current 0.1 mA or less, ON current 2 mA (in case of short circuit)
		Voltage input: Maximum rated input voltage 26.4 V, ON voltage 18 V or more, OFF current 0.2 mA or less, ON current 2 mA (at 24 V)
	Points	8 points (IN1 to IN8)
	function	IN1: External trigger↑↓ /TIMING, IN2 to IN8: can be assigned to any function
		Assignable Functions: Program Switch, Stop Glowing, ZERO / Offset (Batch), Reset (Error Only), Reset (Judgment Value Only), Reset (Judgment Value & Error)
output	output	The open collector output is NPN/PNP switchable and N.O./N.C switchable
		NPN open collector output: 26.4 V max. 50 mA (20 mA when connected to an expansion unit), residual voltage 1.5 V or less
		PNP open-collector output: 26.4 V max. 50 mA (20 mA when connected to an expansion unit), residual voltage 2 V or less
	Points	10 points (OUT1 to OUT10)
	function	It can be assigned to any function
		Assignable functions: Comprehensive judgment result (all OK/any OK/NG), Run, BUSY, Error, position correction result, tilt correction result,
		Black & White Area / Height Area Tool Results (OK/NG), Height / Height Difference /MAXMIN/ Calculation Tool Results (OK/NG/HIGH/LO), Alarm
Analog voltage output		not
Analog current output
Number of programs		32 programs
Statistics		Scan Mode: Measured Value / Concordance (MAX, MIN, AVE), Processing Time (Latest Value, MAX, MIN, AVE), Count (OK / NG / Triggers)
		Straight-line mode: Measured value / Consistency (MAX, MIN, AVE), Count (OK number / NG number / number of judgments) 13
Detection records	Save the quantity	100*4
	Save the condition	NG only/ All optional*4
Ethernet	specification	not
	connector
Interfaces are supported		CC-Link/DeviceNetTM /EtherNet/IPTM /EtherCATⓇ /RS-232C/BCD / PROFINET / PROFIBUS / TCP/IP 输出*5
Number of units that can be connected		1 main unit, 1 expansion unit, and 1 communication unit (DL).
rated	Supply voltage	Supplied by the main unit
	Current consumption	Maximum 1.9 A or less (0.8 A or less when using the main unit only, 1.9 A or less when adding an expansion device) (excluding output load)*6
Environmental resistance	Ambient temperature	0 to +50°C (no freezing)
	relative humidity	35 to 85% RH (non-condensing)
Material		Main Unit Housing: PC/ Power Connectors: PA, POM/ Analog Output Connectors: PA, POM/I/O Connectors: PA/
		Sensor Probe Connector: Zinc + Ni Plating, PA/Ethernet Connector: Copper Alloy + Ni Plating / Rear Heat Dissipator of the Main Unit: Aluminum /
		DIN rail mounting clip on the back of the main unit: POM/ nameplate: PC
weight		Approx. 190 g

*1 Displayed in the control panel for IX or in the PC software.

*2 Can be set according to the program.

*3 When sample hold (edge), peak/valley value/P-P hold (horizontal/edge) is set.

*4 Saved in the internal memory of the sensor controller. The inspection records saved inside the sensor controller can be backed up to a PC via a USB memory installed on the control panel or PC software via the IX.

This article introduces KEYENCE/KEYENCE multi-point laser sensor IX-1050 products, if you are interested in KEYENCE/KEYENCE products, please also contact our customer service, we are looking forward to your call, hope our technology and service can bring you a better experience.

The company has been customer-centric, the concept of creating value for customers, winning the market with quality and service, and sincerely hopes to cooperate with all sectors of society to create success, create brilliance together, and work together to create a better tomorrow! In line with the concept of credibility and service-oriented, the company warmly welcomes new and old customers to inquire, visit and negotiate business

KEYENCE/KEYENCE Multi-Point Laser Sensor IX-1050

Sections viewed

Contact

working hours