Soft Touch/Rorobot Finger Module B7V4 Fingertip travel 75mm

Introduction: Rorobot Finger Module B5V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot Finger Module C7V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot Finger Module B8V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted. Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and ...

Introduction: Rorobot BMC-20603[H]/S Features: The fingertips are opened in the positive pressure state and clamped in the vacuum state, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by supporting the fingertip distance D. Soft-touch materials are divided into regular [H] and non-...

Introduction: Rorobot Finger Module A4V4, Features and Applicable Scenarios: Large clamping force, can be used in series (using screw kit PK) and simplifies the arrangement of the trachea. It is mostly used in the scene where multiple fingers work at the same time and the workpiece is compact, and the workpiece width is generally greater than 50mm. Product Features ...

Introduction: Rorobot Finger Module C6V3, Features and Applicable Scenarios: Independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle can be adjusted Features: Features and applicable scenarios: independent installation, can be installed with SMP sliding mounting plate, finger spacing and angle ...

Introduction: Rorobot ACU-MMN Active Driver, ACU-MMN Active Driver--Standard, Mobile Soft Touch Gripper Special Controller, Output Air Pressure -70-120kPa, Manually Adjust the Clamping Force by Knob. Built-in drive air source and battery, can be fully charged without external power supply ...

Introduction:Rorobot FM-C4V5/LS1[H] Product parameters Positive pressure stroke: 11mm Negative pressure stroke: 3mm Safe working air pressure: 300kPa Recommended load: 70g Self-weight: 20g Our customer-centric approach ...

Introduction: Rorobot Soft Jaw BML-20006 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Soft Touch/Rorobot Quick Change Module QCM-01R, Quick Change Module is used for automatic quick replacement of spare grippers. The quick-change module [QCM] is installed between the flange connection module [FCM] and the end of the robotic arm, and is divided into the robotic arm side (R-side, installed at the end of the robotic arm) and the gripper side (G-side, installed...

Introduction: Rorobot Robot BML-1G071010[LPAS]/S Features: The fingertip is open in the positive pressure state, and the vacuum state is clamped, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted for the distance G between the fingertip and the workpiece. Soft claw material ...

Introduction: Rorobot BMC-4B32[H]/S Features: The fingertips are open in the positive pressure state, and the clamping is in the vacuum state, and it is recommended to use the soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertips G and the outer support fingertips D. Soft claw ...

Introduction: Rorobot BML-3G20[H]/S Features: The fingertips are open in the positive pressure state and clamped in the negative pressure state, and it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G. The soft claw material is divided into conventional type [H] ...

Introduction: Rorobot Finger Module C5V5, Features and Applicable Scenarios: The module is thinner, and the minimum finger spacing of the mounting module is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot soft jaw BML-3A18[H]/S, soft jaw material is divided into conventional type [H] and non-marking type [HAS] Features: The fingertips are open in the positive pressure state, and clamped in the negative pressure state, it is recommended to use it with a soft-touch air driver, and the clamping fingertip distance G and the external support fingertip distance D can be ...

Introduction: Rorobot Robot Soft Jaw FM-A6V3/LS1, Soft Finger LS1 has good versatility and wear-resistant. It is suitable for rough workpiece surfaces such as food, metal, and plastic parts. When gripping the workpiece, the damage caused to the workpiece by the soft finger itself can be minimized. We...

Introduction: Soft Touch/Rorobot Module B-20006/S, B-20006/S is a flexible claw with a small structure, especially suitable for strip and rod workpiece grabbing, which can realize wrapping grabbing, non-trace and non-destructive handling and sorting, to ensure that the product will not be scratched, and reduce the defect rate. When multiple soft jaws are connected in series, ...

Introduction: Rorobot Finger Module B3V5, Features and Applicable Scenarios: The module is thinner and lighter, and the minimum finger spacing between the mounting modules is only 10mm, which is suitable for clamping tiny, thin and light workpieces. It can also be used in series (using the screw kit PK), but compared to the V4, each finger needs to be supplied with air independently.

Introduction: Rorobot Soft Jaw BMC-20802 Features: The fingertips are open in the positive pressure state, and the vacuum state is clamped, so it is recommended to use it with a soft-touch air drive, and the working air pressure can be adjusted by clamping the fingertip distance G The soft claw material is divided into conventional type and non-marking type.

Introduction: Rorobot Finger Module FM-A8V1, Features and Applicable Scenarios: Combination of Two-Finger Module, Compact Structure, Small Footprint. The spacing and installation angle are not adjustable, which is suitable for clamping tiny, thin and light workpieces. Features: Features and applicable scenarios: two-finger ...