Panasonic sensor PNP open collector transistor dual output analog current output FX-505P-C2

Panasonic sensor PNP open collector transistor dual output analog current output FX-505P-C2, PNP open collector transistor, maximum source current: 50mA, applied voltage: 30V DC or less
Panasonic sensor PNP open collector transistor dual output analog current output FX-505P-C2

project	content
Order product number	FX-505P-C2
Model	FX-505P-C2
Supply voltage	12~24V DC±10% pulsation P-P10% or less
Power consumption	Typical: 960 mW or less (excluding power supply voltage 24 V, current consumption 40 mA or less, and monitoring current output)
Power consumption	ECO mode: 680 mW or less (excluding power supply voltage 24 V, current consumption 28 mA or less, and monitoring current output)
Output 1, output 2	PNP open-collector transistors
	・Maximum source current: 50mA (Note 1)
	・Applied voltage: 30V DC or less (between output and +V)
	・Residual voltage: 2 V or less (Note 2) (at maximum source current)
	Note 1: 50 mA for connector type with more than 5 connectors.
	Note 2: When using a 5-meter-long one-touch cable (sold separately).
Output 1 and output 2: the number of output points	2 points
Output 1 and Output 2: Output actions	L/D mode can be used to switch between ON when light is in or ON when light is not in light
Output 1 and Output 2: Short circuit protection	Equipped with
Reaction time	H-SP: 25μs or less
	FAST: 60μs or less
	STD: 250μs or less
	LONG: 2 ms or less
	U-LG: 4 ms or less
	HYPR: 24ms or less Switchable
Monitor the current output	Output current: Approx. 4~20mA [H-SP, FAST, STD: 0~4,000 display, LONG: 0~8,000 (Note)]
	Reaction time: less than 2ms
	Zero point: within 4mA±1% F.S
	Span: within 16mA±5% F.S
	Linearity: within ±3% F.S
	Load resistance: 0~250Ω
	Note: Not applicable after setting the display adjustment.
External inputs	PNP contactless input
	・Signal conditions
	High:+4V~+V DC (Signal condition: 3mA)
	Low: 0~+0.6V DC or off
	・Input impedance: Approx. 10kΩ
External Input (Switching Output 2)	-
External input correspondence function	Switching type: Drop light stop, teach (fully automatic, limited, 2-point teach) / Logic operation setting / Lock / Display adjustment / Database load / Database save
How to set the sensitivity	2-point teaching/limited teaching/automatic teaching/manual adjustment
The amount of light entering the display range	H-SP/FAST/STD：0～4,000
	LONG：0～8,000
	U-LG/HYPR：0～9,999
Timer function	<输出1>Disconnect Delay Timer / On Delay Timer / One-shot Timer / Turn On • Off Delay Timer / On Delay • One-shot Timer Active/Invalid Switching Timer The timer is variable
Timer function	<输出2>Disconnect Delay Timer/On Delay Timer/One-shot Timer Active/Inactive Switching Timer The timer time is variable
Timer function: Timer time	Timer range "ms": Approx. 0.5 ms, approx. 1~9,999 ms, approx. 1 ms increments
	Timer range "sec." : about 0.5s, about 1~32s, about 1s units
	Timer range "1/10ms": 0.05ms, 0.1~999.9ms, 0.1ms
	Each output is set separately
Adjustable amount of light emitted	Equipped with 3 levels (25~100% for each level) + automatic setting [1 level (25~100%) for H-SP]
Anti-jamming function	Equipped with (Note) Auto/Frequency Switching Type
	Note: As shown in the table below, when using the automatic interference prevention function, the number of fiber heads that can be attached to each other varies depending on the reaction time. When using the different frequency anti-interference function, the number of fiber heads can be installed close to each other, and the maximum number of installations is 3.
	・Number of optical fiber heads that can be installed (unit: set)
	Reaction time: IP-1
	H-SP：0
	FAST：2
	STD：4
	LONG：8
	U-LG：8
	HYPR ：12
Various settings	Difference setting, transfer setting, projection setting, display reversal setting, ECO setting, database loading and saving setting, copy setting, code setting, reset setting, logic operation setting, benchmark tracking cycle setting, etc
Protective structures	IP40(IEC)
Use ambient temperature	-10~+55°C [-10~+50°C when 4~7 units are close together, -10~+45°C when 8~12 units are close together] (note that condensation and freezing are not allowed), storage: -20~+70°C
Projection Element (Modulated)	Red LED (Emission peak wavelength: 643nm)
Material	Shell, cover: Polycarbonate (Note)
	Switch: Polyester elastomer
	Note: Specifications are changed according to Panasonic brand products.
cable	0.2mm2 6-core rubber cable, 2m long
Cable extension	The total length of the cable of 0.3 mm2 or more can be extended to 100 m (the supply voltage is 12 V DC or more)
weight	Body weight: Approximately 60 g
weight	Package weight: about 100g
accessory	FX-MB1 (amplifier protection seal): One set

Panasonic sensor PNP open collector transistor dual output analog current output FX-505P-C2, PNP open collector transistor, maximum source current: 50mA, applied voltage: 30V DC or less. 76 Technology with quality assurance, with excellent reputation, so that you are comfortable in the purchase, rest assured in use, 76 Technology, need your trust and support.

Panasonic sensor PNP open collector transistor dual output analog current output FX-505P-C2

Sections viewed

Contact

working hours