XINJE DM5F-2A Servo Drive

Uploaded on 2023-12-20 10:25

Product introduction: flat appearance structure design, convenient wiring, saving installation space; Support gantry synchronization to achieve dual-axis precise synchronization; Support Modbus RTU, EtherCAT (under development, stay tuned), CANopen (under development, stay tuned) multiple communication protocols; Built-in electronic cam (under development, stay tuned), dual-axis simultaneous interpolation function (under development, stay tuned), more accurate positioning, faster response...
XINJE DM5F-2A Servo Drive

Product Description:

Three control modes, seamless switching: position control, speed control, torque control

6 SI inputs, 6 SO outputs

Input Patterns: Pulse + Direction, AB Phase Pulse, CW/CCW Signal

Input frequency: 200kpps open collector, 500kpps differential

Interface circuits: collector (+24V level), differential (+5V level)

Communication port: RS232, RS485 standard

Specifications:

Project: DM5F series 2-in-1 servo

Basic Specifications:

Power range: 0.4~0.75KW

Input Power:
Single-phase AC200~240V;
Three-phase AC200~240V, use 50/60Hz;

Encoder Feedback:
17Bit/23Bit communication encoder

Control mode:
Three-phase full-wave rectification IPM PWM control, sine wave current drive mode

Operating Environment:

Ambient Temperature:
Operating: -10~+40°C (no condensation) / Storage: −20~+60°C (no condensation)

Ambient Humidity:
Run/Storage: 90% RH or less (no condensation)

Vibration/Shock Resistance:
4.9m/s2/ 19.6m/s2

Function:

Protection Functions:
Overvoltage, undervoltage, overheating, overcurrent, overload, overspeed, analog input abnormality, excessive position deviation, output short circuit, encoder abnormality, regeneration abnormality protection, overtravel protection, oscillation protection, operation disconnection protection, etc

Dynamic Brakes:
not

Communication Functions:
RS232/RS485: STANDARD MODBUS RTU PROTOCOL

Braking Resistance:
Built-in braking resistor, external braking resistor can be connected

Display & Operation:
5-digit LED indicator, power indicator, 2 running indicators, 4 button operation

Load Variation Rate:
0~100% load: ±0.01% or less (at rated speed)

Voltage rate of change:
Rated voltage±10%: 0.01% (at rated speed)

Rate of change in temperature:
20±25°C: ±0.1% or less (at rated speed)

Input and output signals:
Position Output:

Output form:
ABZ phase 5V differential

Crossover function:
In the tank

Collector Z-phase output:
In the tank

Analog Inputs:
not

Digital Inputs:
6 SI inputs
Servo Enable, Alarm Clear, Forward Rotation Prohibited, Reverse Rotation Disabled, Torque Limit Selection, Internal Speed Selection, Gear Ratio Switching, Mode Switching, Pulse Input Disabled, Zero-Speed Locking, Position Deviation Clearing, Internal Position Changing Signal, Internal Control Mode Direction Switching

Digital Outputs:
6 SO inputs
Positioning Complete, Servo Ready, Alarm Output, Torque Limit Output, Same Speed Detection, Rotation Detection, Speed Arrival, Brake Release Output, Warning Output

Position Control Mode:
Maximum Input Pulse Frequency:
Open collector: 200kpps
Differential: 500kpps

Pulse Command Mode:
It can accept 3.3~5V, 18~24V pulse + direction, AB phase pulse, CW/CCW signal

Control mode:
External pulse/built-in position

Feedforward Compensation:
0~100% (set resolution to 1%)

Positioning completion width setting:
0~65535 instruction units (set resolution to 1 instruction unit)

Electronic Gear Ratio:
1/10000≤B/A≤10000

Speed Control Mode:
Control mode:
Internal three-speed mode, external speed mode

Command smoothing method:
Low-pass filter, smoothing filter

Analog Inputs:
Voltage Range:
not

Input Impedance:
not

Torque Limit:
Internal parameters

Rate of change in velocity:
When the rated load changes by 0~100% of the external load: ±0.01% or less (at rated speed)
Rated voltage±10%: 0.01% (at rated speed)
Ambient temperature 20±25°C: ±0.1% or less (at rated speed)

Torque Control Mode:
Control mode:
Internal torque

Command smoothing method:
Low-pass filter, smoothing filter

Analog Inputs:
Voltage Range:
not

Input Impedance:
not

Speed limit:
In the tank

Bus Control Mode:
Number of control axes:
not

Communication Protocol:
not

The company respects the enterprise spirit of "practicality, hard work and responsibility", and creates a good corporate environment with integrity, win-win, and business philosophy, and takes a new management model, perfect technology, thoughtful service, and excellent quality as the foundation for survival. We always adhere to: customer first, serve customers attentively, and insist on impressing customers with their own services. Always adhering to the business philosophy of "integrity, win-win", relying on excellent prices, excellent quality, fast delivery and pre-sales consultation and after-sales service to win the trust of our customers.

　　This article introduces the XINJE/XINJE servo drive DM5F-2A 0.4~0.75KW 6CH SI input, 6CH SO output products, if you are interested in XINJE/XINJE standard PLC, please also contact our customer service, we look forward to your call, hope our technology and service can bring you a better experience.

XINJE DM5F-2A Servo Drive

Sections viewed

Contact

working hours