Schneider inverter ATV12PU22M3 2.2 kW 3hp

Introduction: ATV12 Schneider inverters are used in three-phase asynchronous motors with a power range of 0.18kW to 4kW. The ATV12 Schneider inverter is easy to install (based on the plug-and-play principle), compact and multi-functional, and available in a base version, making it particularly suitable for simple industrial machinery or some civilian equipment.

Schneider/Schneider ATV12PU22M3

Product parameters

Product family Altivar 12

Product Type: Inverter

Product function Asynchronous motor

Applications: Simple machinery

Assemble on the bottom plate

Component name ATV12

Quantity per set: 1 pcs per set

EMC Filters There are no EMC filters

Built-in fan None

The number of phases of the grid is 3 phases

Rated supply voltage [US] 200...240 V - 15...10 %

Motor power (kW) 2.2 kW

Motor power 3 hp

Communication protocol Modbus

Line current 14.9 A 200 V

　　12.5 A 240 V

Speed range 1...20

Instantaneous over-torque 150...170 % Rated motor torque depends on the rated value of the drive and the type of motor

Asynchronous Motor Control Profile Sensorless flux vector control

Voltage frequency ratio (V/f)

Secondary voltage/frequency ratio

IP protection class IP20 upper part without blind plate

Noise level 0 dB

Additional information: Power supply frequency 50/60 Hz +/- 5 %

Port Type 1 RJ45 Modbus front panel

Physical interface: 2-wire RS485 Modbus

Transmission frame RTU Modbus

Transmission rate 4800 bit/s

　　9600 bit/s

　　19200 bit/s

　　38400 bit/s

Address number 1...247 Modbus

Communication Services Read Hold Register (03) 29 words

Write single register (06) 29 words

Write multiple registers (16) 27 words

Read/Write Multiple Registers (23) 4/4 words

Read Device Identification (43)

Expected line Isc < = 5 kA

Continuous output current 10 A 4 kHz

*Large transient current 15 A 60 s

The output frequency of the frequency converter is 0.5...400 Hz

Rated switching frequency 4 kHz

The switching frequency from 2 to 16 kHz is adjustable

4...16 kHz with derating factor

Braking torque up to 70% of motor torque without braking resistor

Motor slippage compensation is preset at the factory

adjustable

Output voltage 200...240 V 3 phase

Electrical connection terminals 5.5 mm² AWG 10 L1, L2, L3, U, V, W, PA, PC

Tightening torque 1.2 N.m

Isolate the circuit between the power supply and the control

Power supply: Internal power supply for reference potentiometer 5 V dc 4.75...5.25 V 10 mA overload and short circuit protection

Internal power supply for logic input 24 V dc 20.4...28.8 V 100 mA overload and short-circuit protection

Analog input quantity 1

Analog input type Configurable voltage AI1 0...10 V 30 kOhm

Configurable voltage AI1 0...5 V 30 kOhm

Configurable current AI1 0...20 mA 250

Discrete input quantity 4

Digital Input Type Programmable LI1... LI4 24 V 18...30 V

Discrete input logic Negative logic (drain) > 16 V < 10 V 3.5 kOhm

Positive Logic (Source) 0... < 5 V > 11 V

< 20 ms +/- 1 ms logic input during sampling

< 10 ms analog input

Linearity error '+/- 0.3 % *large analogue input

Number of analog outputs 1

Analog output Model Software - configurable voltage AO1 0...10 V 470 8 bits

Software - Configurable current AO1 0...20 mA 800 8 bits

Number of discrete outputs: 2

Output Type Logic Output LO+, LO-

Relay output protection R1A, R1B, R1C 1 C/O

*Small switching current [Imin] 5 mA 24 V DC logic relay

*Large switching current 2 A 250 V AC inductive load cos phi = 0.4 L/R = 7 ms logic relay

2 A 30 V DC inductive load cos phi = 0.4 L/R = 7 ms logic relay

3 A 250 V AC resistive (load) cos phi = 1 L/R = 0 ms logic relay

4 A 30 V DC resistive (load) cos phi = 1 L/R = 0 ms logic relay

Acceleration and deceleration tilt S

　　U

Linear from 0 to 999.9 s

Braking to stop using DC injection 0.1...30 s

Protection Type Prevents loss of three-phase input phase

The thermal protection of the motor is continuously calculated by means of a drive, and I²T is calculated

Line power supply overvoltage

The bus power supply is under-voltaged

Overcurrent between the output phase and ground

Overheat protection

Short circuit between the phases of the motor

Frequency resolution 0.1 Hz display unit

A/D converter, 10-bit analog input

The time constant 20 ms +/- 1 ms is used for model changes

Identify CE

Operating position +/- 10° vertically

Height 143 mm

Width 105 mm

Depth 98.2 mm

Product weight 1 kg

Discrete vs. Process Manufacturing Commercial e

The company respects the enterprise spirit of "practicality, hard work and responsibility", and creates a good corporate environment with integrity, win-win, and business philosophy, and takes a new management model, perfect technology, thoughtful service, and excellent quality as the foundation for survival. We always adhere to: customer first, serve customers attentively, and insist on impressing customers with their own services. Always adhering to the business philosophy of "integrity, win-win", relying on excellent prices, excellent quality, fast delivery and pre-sales consultation and after-sales service to win the trust of our customers.

This article introduces Schneider ATV12PU22M3 2.2 kW 3hp products, if you are interested in Schneider inverter, please also contact our customer service, we are looking forward to your call, hope our technology and service can bring you a better experience.

Schneider inverter ATV12PU22M3 2.2 kW 3hp

Sections viewed

Contact

working hours