Common types of EVOC industrial computers

Control of production lines and machines: The industrial computer can accurately control various industrial production lines and related machinery and equipment through various control methods and algorithms, complete precise operation and close monitoring. Collect and detect data: The IPC can pass through a variety of sensors and monitoring equipment to collect ...

1. Close the auto-start item of the system boot file 2. RUN SCANDISK TO CHECK THE DISK FOR BAD SECTORS 3. Run the disk defragmenter to eliminate the fragmentation 4. Run the Disk Cleaner to eliminate the ...

The traditional industrial computer uses a combination of 4U and other types of cold-rolled plate chassis + gold finger motherboard (full-length or half-length card) + base plate + high-power power supply. There are a number of unstable elements to such a structure: 1. If the CPU card is inserted into the baseboard, there will be a bad touch phenomenon, such as vibration.

BIOS is the primary information reading direction when the IPC is started, if it is not set properly, the IPC will not be able to boot normally. When the IPC fails to start normally, it can complete the repair of unknown faults by restoring the BIOS factory settings. So how about the industrial motherboard BIOS...

1. Device operation system First: Review the settings in the CMOS and restore to factory settings if needed. Secondly: pay attention to the parameters of the hard disk, the temperature of the CPU, etc. Observe whether the information displayed during the self-test of the industrial computer is consistent with the actual hardware equipment. 2. Device software ...

Overview of the system Broadband cell access is to separate the switching function and transaction control function of the switch, and set up some functional components realized by the computer software system on the switching network, and the provision and control of all new transactions are jointly completed by these functional components in cooperation with the original switch. Plan...

When selecting a high-speed data acquisition card, the following goals are generally considered: Sample rate, resolution, number of channels, bus, etc. The selection of the key depends on what your high-speed data acquisition card is for, so as not to blindly select the data acquisition card. Because different data acquisition cards are used in different places ...

Industrial motherboards are widely used in self-service terminals, medical instruments, industrial control, automation equipment, telecommunications, electric power, network, rail transit and other fields in terms of planning, materials, production, manufacturing, etc., attaching importance to reliability, vibration resistance, wide temperature and other characteristics. ...

When selecting industrial computers, we often encounter PCI and PCI-e expansion slots, what are the differences between the two? 1. The color is different. In IPC motherboards, the PCI slot is milky white, while the PCI-e slot is black. 2. The transmission rate is different. PCI slot max data ...

1. The all-steel chassis of IPC is designed according to the standard, anti-shock, anti-vibration, anti-electromagnetic disturbance, and a passive base plate compatible with PC-bus can be installed inside. 2. The slots of the passive backplane are composed of multiple slots of ISA and PCI bus, and the number of ISA or PCI slots is ...

1. The dustproof and waterproof performance of the fully enclosed planning dustproof and waterproof embedded industrial control all-in-one machine is necessary in industrial use. The front panel is integrated die-casting, and the fit between the face and frame is more consistent, and at the same time, participating in the waterproof strip planning, it can reach the IP65 waterproof and dustproof of the whole machine, which is more suitable for evil.

1. The industrial computer "crashes" due to hardware reasons Reason analysis: When the industrial computer processes too many on-site signals transmitted by the PLC, the CPU frequency of the industrial computer is low, and the memory is small, so it is impossible to identify and process so many signals together, so that these signals "crash" and form an industrial ...

The main structure and working principle of the industrial computer are the same as those of the general computer, but the difference is that the industrial computer adopts a steel structure chassis with fixed strips inside, which has high anti-magnetic, dustproof and anti-oscillation capabilities, and is suitable for messy industrial sites. ...

What is a multi-operation system? The multi-operation system refers to the installation of multiple industrial computer operation systems on one computer, and each system is independent of each other. Users can install other versions of the system on the basis of the original system. The multi-operation system is used more in daily life, and it is used in the ...

The full English name of PLC is Program mable Logic Controller, which was produced in the early 70s of the 20th century. The earliest PLC appeared as a replacement relay system, and its main function was only a logical and simple sequential control function. ...

Commercial switches are commercial Ethernet switches, which are generally used in enterprise work networks and other occasions, and are generally rack-type, installed in enterprise computer rooms, and generally require high reliability, 24-hour uninterrupted long-term operation, large bandwidth, and more interfaces. ...

Detection method and sequence of industrial computer failure not starting: 1. Check the three major operating conditions of the CPU Power supply clock reposition 2. Remove the BIOS and check whether the 22-pin chip selection signal has jumped 3. Try changing the BIOS and check the line connected to the BIOS 4 ...

When this host issue occurs, the first thing we need to check is the BIOS. The BIOS of the motherboard stores important hardware data, and the BIOS is also a relatively fragile part of the motherboard, which is very vulnerable to damage, and once damaged, it will lead to the failure of the system to operate.

Memory is one of the most important components in industrial motherboards, which is mainly used to temporarily store the computing data in the CPU and the data exchanged by external memory. In the operation of industrial computers, there may be incompatibility between memory and industrial motherboards. The following is an introduction to the incompatibility of memory with industrial motherboards ...

One. Buy a little common sense 1. The current is very small In fact, many users will ignore the size of the current when buying the power supply of the industrial computer, and then the tragedy of the operation will occur, so we are reminded to pay attention to the size of the current when buying the power supply of the industrial computer. 2. Accepted voltage ...