IDEC/Izumi HS7A-DMC non-contact safety switch HS7A-DMC5915

Compact 3-position enable switch with auxiliary contacts. Ergonomic OFF→ ON → OFF 3-position action for hazard avoidance. Between pressing OFF (position 3) → releasing OFF (position 1), the structure of the ON state is not formed. IEC60204-1（2005） ...

By connecting the signal of the auxiliary contact directly to the PLC, the operation of each HS7A-DMP non-contact safety switch can be monitored. Ideal for installation on protective doors where positioning is difficult. With the appropriate combination of dedicated safety relay modules, it is possible to correspond to safety category 4 and can be connected to up to 36 groups, protection, etc.

IDEC/Izumi Safety Interlock HS1T Heavy Duty Locking HS1T-VG7Y4ZSM-G 4 contacts 2NC, 1NO and 1NC, solenoid lock, side wires 5000N locking force is the smallest in the industry Spring-loaded terminals prevent loose wires Energy saving 200mA solenoid consumption Electromagnetic locks and snap locks are available ...

During mechanical operation, the guards/keys are securely locked. Remove the key to unlock the safety gate, and keep the load circuit and auxiliary circuit open. Ideal for applications where the key needs to be taken into a hazardous location to avoid accidental start-up of the device. Key interlock type ...

The HS6B is the smallest three-contact enable switch on the market today and can be installed in even the tightest areas, so you can be sure of safety in every necessary location. The design consists of a total of 3 contacts, a double load contact and a monitoring contact (according to ISO13849-1, EN954-1 ...

IDEC/Izumi Safety Interlock HS1T Heavy Duty Locking HS1T-VW44ZM-G 4 contacts 1NO and 3NC, spring lock 5000N locking force is the smallest in the industry Spring-loaded terminals prevent loose wires Energy saving 200mA solenoid consumption Electromagnetic lock and snaplock models are available Mechanical Specifications ...

3 position action of OFF ⇒ ON ⇒ OFF to avoid danger. Pressing ON ⇒ OFF is a direct open-circuit action function. By pressing OFF (position 3) ⇒ releasing OFF (position 1), there is no structure in the ON state. （IEC60204-1； 9.2.5.8 ...

4 Contacts, 1NC 1NO Gate, 1NC 1NO Lock Monitoring Circuit, Electromagnetic Lock Compact body: 35x40x127mm 1400N locking strength Gold-plated contacts for small loads The head direction can be rotated 8 different actuator entries are allowed Applicable standard: EN ISO14119 G ...

VD circuit, key detachable in all positions, 5m cable Mechanical Specifications: Product Category Safety Interlocks Key removal location for all positions Environmental indicators Degree of protection IP65 Installation and installation specifications Cable length: 5 meters Our customer-centric service concept: all-round ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

It is equipped with a "operation head detachment detection function" that turns the main circuit (11-12) into the OFF state when the operating head falls off. It is the same size as the HS5B type (external dimensions, mounting dimensions), and is available as a 3-contact model with dual contacts + auxiliary contacts. Small size allows installation in confined places ...

IDEC/Izumi HS6E Submersible Locking HS6E-P7Y4B01-G Safety Switch Solenoid LockThe World's Thinnest Solenoid Interlock Switch 15mm wide Flexible installation - reversible mounting and angled cables allow for four actuator insertion directions Energy saving - 24V DC/110 mA Manually unlockable on three sides ...

3-position action of OFF ⇒ ON ⇒ OFF for danger avoidance. Press OFF (position 3) ⇒ release OFF (position 1) to create an ON structure. (IEC60204-1:2005, 10.9, IEC60947-5-8:2007, 7.1.9), built-in 2 ...

Introduction: VA circuit, key detachable in all positions, key 502, 3m cable Product Category Safety Interlocks Key removal location for all positions Degree of protection IP65 Cable length 3 meters Our customer-centric service concept: a full range of services are pursued as a high...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

ø16 world *** 4 contact, 27.9mm short carcass emergency stop button switch. The safety disconnection action that pursues the limit of safety Ø16mm×19.5mm The world's largest small-grade short carcass integrated type*** is suitable for machines with limited internal space. Rounded corners and curved button type, the button surface is not ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

VA circuit, key detachable in all positions, 5m cable Mechanical Specifications: Product Category Safety Interlocks Key removal location for all positions Environmental indicators Degree of protection IP65 Installation and installation specifications Cable length: 5 meters We...

Ergonomic OFF ⇒ ON ⇒ OFF 3-position action for danger avoidance. Position 1 ⇒ 2, built-in snap-action switch with a light operating feel, making position 2 easy to identify. Position 2 ⇒ 3 requires force and a clear sense of operation. Reduction of operating force in position 2 ...

Most safety interlocks on the market typically have up to 6 contacts, which exceeds the requirements of many applications. The revised EN ISO 14119 standard requires two interlocking devices to achieve PLe when using Class 2 interlocked devices. For one of the two interlocks, the 2 contacts ...