IDEC/Izumi HS6E Submersible Locking HS6E-M7Y4B01-G Safety Switch Solenoid Lock

IDEC/Izumi HS6B Subminiature HS6B-03B01 Safety Interlock Switch 3NC 3NC Contact, 1m Cable 30x15x78mm enclosure One-piece cables reduce wiring time IP67 (IEC60529) waterproof sealing (contact sealing; The enclosure allows for drainage) Direct door opening action ...

IDEC/Izumi HS6B Subminiature HS6B-11B03 Safety Interlock Switch 1NC1NO 1NC 1NO Contact, 3m Cable 30x15x78mm enclosure One-piece cables reduce wiring time IP67 (IEC60529) waterproof sealing (contact sealing; The enclosure allows for drainage) Open directly ...

It is equipped with a "operation head detachment detection function" that turns the main circuit (11-12) into the OFF state when the operating head falls off. It is the same size as the HS5B type (external dimensions, mounting dimensions), and is available as a 3-contact model with dual contacts + auxiliary contacts. Small size allows installation in confined places ...

IDEC/Izumi HS6E Submersible Locking HS6E-P7Y4B03-G The world's thinnest solenoid interlock switch 15mm wide Flexible installation - reversible mounting and angled cables allow for four actuator insertion directions Energy saving - 24V DC/110 mA Three sides can be manually unlocked LED Indicator ...

Small size (external dimensions: 7mm× 16mm×51mm). Simple alignment during installation. Up to 36 sets can be connected. (When using a safety relay module: HR1S-DME type). IP67 protection structure. Mechanical Specifications: Contact structure 1NC+1NO Functional Specifications: Detection distance ...

Ergonomic, 3-position action of OFF ⇒ ON ⇒ OFF for danger avoidance. Position 1 ⇒ 2, built-in snap-action switch with a light operating feel, making position 2 easy to identify. Position 2 ⇒ 3 requires force and a clear sense of operation. Reduction of operating force in position 2 ...

3 position action of OFF ⇒ ON ⇒ OFF to avoid danger. Pressing ON ⇒ OFF is a direct open-circuit action function. By pressing OFF (position 3) ⇒ releasing OFF (position 1), there is no structure in the ON state. （IEC60204-1； 9.2.5.8 ...

The non-contact safety switch with RFID technology improves the safety performance. Built-in safety features make the construction of a safety system independent of the combination with specific modules. Thanks to the RFID method, there is no error even if the door closes slowly. Even when installed on swing doors, sliding ...

All M3.5 wiring screws are used to improve the connection line. The contact structure is 2 circuits with 1NC+1NC main circuit and 1NC auxiliary circuit, and it is possible to support dual main circuit + lock monitoring circuit. There is also a key with a portable key as standard for hostage control ...

It is equipped with a "operation head detachment detection function" that turns the main circuit (11-12) into the OFF state when the operating head falls off. It is the same size as the HS5B type (external dimensions, mounting dimensions), and is available as a 3-contact model with dual contacts + auxiliary contacts. Small size allows installation in confined places ...

VA circuit, pull out the key in the UNLOCK position, key 502, 3m cable, rear unlock button Mechanical Specifications: Product Category Safety Interlocks Key Removal Position Removed in the unlocked position Environmental indicators Degree of protection IP65 Cable length 3 meters Our customer-centric approach ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

By connecting the signal of the auxiliary contact directly to the PLC, the operation of each HS7A-DMP non-contact safety switch can be monitored. Ideal for installation on protective doors where positioning is difficult. With the appropriate combination of dedicated safety relay modules, it is possible to correspond to safety category 4 and can be connected to up to 36 groups, protection, etc.

All M3.5 wiring screws are used to improve the connection line. The contact structure is 2 circuits with 1NC+1NC main circuit and 1NC auxiliary circuit, and it is possible to support dual main circuit + lock monitoring circuit. There is also a key with a portable key as standard for hostage control ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

VA circuit, key removal at LOCK position, 3m cable, rear unlock button Mechanical Specifications: Product Category Safety Interlocks Key Removal Position Removed in the locked position Environmental indicators Degree of protection IP65 Installation and installation specifications Cable length 3 meters We are customer-centric ...

There is no need to perform the angle adjustment of the component end, and the position determination is simple and convenient. It can be installed horizontally and vertically, and can be easily mounted on various doors. Key features: There is no need to perform the angle adjustment of the component end, and the position determination is simple and convenient. It can be installed horizontally and vertically, and can be easily installed ...

The actuator is mounted on the guard, the safety switch is mounted on the mechanical body, and the mechanical locking guard is installed. When the inertial action of the machine stops, the electromagnetic coil excitation is unlocked by an electrical signal from the controller, etc., for greater safety. In the event of a power outage and maintenance, special tools can be used ...

Ergonomic OFF ⇒ ON ⇒ OFF 3-position action for danger avoidance. Position 2 ⇒ 3 requires force and a clear sense of operation. Between pressing OFF (position 3) → releasing OFF (position 1), the structure of the ON state is not formed. IEC60204-1（2005） ...