IDEC/Izumi HS6E-P44B01-G Safety Switch Springlock

Small size: 30mm× 30mm×90mm, by changing the mounting direction of the top, the actuator can be inserted from 8 positions, so as to meet different installation needs. IP67 (IEC60529) protection structure is used for the contact parts. The NC contact has a direct disconnect operation structure. （IEC/EN60947 ...

IDEC/Izumi HS1T Electromagnetic Safety Switch A high-locking strength solenoid safety switch suitable for large doors and large equipment. Key features: Locking strength of 5,000N or more, small size. Rear locking release mechanical finger that can be confirmed on both the front and side ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

IDEC/Izumi Safety Interlock HS5D Micro HS9Z-LH5KLHS5 Plastic Slide Communicator Plastic Slide Handle Actuator for HS5 Series with Key and Rear Lever Product Category: Door Handle Actuators The company has always been customer-centric, the concept of creating value for customers, and the concept of ...

IDEC/Izumi HS6B Subminiature HS6B-02B01 Safety Interlock Switch 2NC Contact, 1m Cable 30x15x78mm enclosure One-piece cables reduce wiring time IP67 (IEC60529) waterproof sealing (contact sealing; The enclosure allows for drainage) Direct door opening action: even if ...

By connecting the signal of the auxiliary contact directly to the PLC, the operation of each HS7A-DMP non-contact safety switch can be monitored. Ideal for installation on protective doors where positioning is difficult. With the appropriate combination of dedicated safety relay modules, it is possible to correspond to safety category 4 and can be connected to up to 36 groups, protection, etc.

Key features: 2 contacts 2NC, spring lock, side conduits 5000N locking force is the smallest in the industry Spring-loaded terminals prevent loose wires Energy saving 200mA solenoid consumption Electromagnetic lock and snaplock models are available Mechanical Specifications: Catheter opening M20 Catheter size M20 The main contact ...

IDEC/Izumi Safety Switch HS6E Electromagnetic Safety Switch HS6E-N7Y4B01-G The main features are 75mm×15mm×75mm. The 15mm thick solenoid safety switch is the leading level in the industry. The actuator is installed on both sides of the switch to provide four insertion directions; Diagonally protruding ...

Ergonomic, 3-position action of OFF ⇒ ON ⇒ OFF for danger avoidance. Position 1 ⇒ 2, built-in snap-action switch with a light operating feel, making position 2 easy to identify. Position 2 ⇒ 3 requires force and a clear sense of operation. Reduction of operating force in position 2 ...

Ergonomic, 3-position action of OFF ⇒ ON ⇒ OFF for danger avoidance. Position 1 ⇒ 2, built-in snap-action switch with a light operating feel, making position 2 easy to identify. Position 2 ⇒ 3 requires force and a clear sense of operation. Reduction of operating force in position 2 ...

During mechanical operation, the guards/keys are securely locked. Remove the key to unlock the safety gate, and keep the load circuit and auxiliary circuit open. Ideal for applications where the key needs to be taken into a hazardous location to avoid accidental start-up of the device. Key interlock type ...

All M3.5 wiring screws are used to improve the connection line. The contact structure is 2 circuits with 1NC+1NC main circuit and 1NC auxiliary circuit, and it is possible to support dual main circuit + lock monitoring circuit. There is also a key with a portable key as standard for hostage control ...

Small size: 30mm× 30mm×90mm, by changing the mounting direction of the top, the actuator can be inserted from 8 positions, so as to meet different installation needs. IP67 (IEC60529) protection structure is used for the contact parts. The NC contact has a direct disconnect operation structure. （IEC/EN60947 ...

Achieve an ergonomic grip. Built-in two hand-held enable switches with 3 positions. 3 position action of OFF ⇒ ON ⇒ OFF to avoid danger. Pressing ON ⇒ OFF is a direct open-circuit action function. Use OFF (position 3) ⇒ release ...

By connecting the signal of the auxiliary contact directly to the PLC, the operation of each HS7A-DMP non-contact safety switch can be monitored. Ideal for installation on protective doors where positioning is difficult. With the appropriate combination of dedicated safety relay modules, it is possible to correspond to safety category 4 and can be connected to up to 36 groups, protection, etc.

IDEC/Izumi HS6B Subminiature HS6B-11B01 Safety Interlock Switch 1NC1NO 1NC 1NO Contact, 1m Cable 30x15x78mm enclosure One-piece cables reduce wiring time IP67 (IEC60529) waterproof sealing (contact sealing; The enclosure allows for drainage) Open directly ...

The non-contact safety switch with RFID technology improves the safety performance. Built-in safety features make the construction of a safety system independent of the combination with specific modules. Thanks to the RFID method, there is no error even if the door closes slowly. Even when installed on swing doors, sliding ...

Round operating section with ø16 mounting holes for easy installation. Suitable for small teach pendants with 2-contact 3-position switches. Key features: Ergonomic OFF ⇒ ON ⇒ OFF 3-position action for danger avoidance. Position 1 ⇒ 2, built-in snap-action switch with a light ...

VD circuit, key detachable in all positions, key 501,3m cable Mechanical Specifications: Product Category Safety Interlocks Key removal location for all positions Environmental indicators Degree of protection IP65 Installation and installation specifications Cable length 3 meters Our customer-centric approach ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.