Banner Engineering launches BSP02 series small PLC upstart

1. Correct installation method of pressure sensor: (1) Verify the frequency response value of the pressure sensor under normal atmospheric pressure and standard temperature conditions with appropriate instruments. (2) Verify the correctness of the code of the pressure sensor and the corresponding frequency response signal. 2. ...

In the field of measurement and control, sensors designed by a certain principle can measure a variety of non-electric power at the same time, and sometimes a non-electric power can be measured by a variety of sensors of different principles, so there are many classification methods for sensors, which can generally be classified according to the following methods. 1. Sort by input ...

1. For example, if an emergency stop switch is installed on some machines, then when the machine fails or is in danger, we can cut off the power supply and stop the operation of the equipment through the installed emergency stop switch, so as to protect the safety of people and equipment. The emergency stop switch is usually manually controlled ...

peculiarity 1. Because the prism is used in the reflector, its detection performance is higher and more reliable than that of the general reflective light-controlled sensor 2. Compared with the detached photosensor, the circuit connection is simpler and easier. 3. The design of the child and mother buckle is embedded, and the safety ...

1. Use the 4 fixing screw holes at the bottom to install directly or add protection or other mechanical use according to the needs of the site and machine installation space facilities. 2. When installing the stainless steel cable, it is necessary to pay attention to the horizontal angle, that is, to make the mechanism of the steel cable from the outlet to the moving part as much as possible, and slide horizontally during work.

(1) Fork photoelectric sensor Placing an optical transmitter and a receiver facing each other on either side of a slot is a fork photoelectric. The luminaire emits infrared or visible light, and the light receiver receives the light in an unobstructed condition. But when the detected object passes through the slot, the light is blocked ...

(1) When the grating ruler displacement sensor is connected to the digital display table, the power must be cut off, and the power supply will be provided after the plug is linked. (2) The grating ruler displacement sensor should prevent foreign objects from entering its interior, including water, oil, dust, etc., so a protective cover should be installed as much as possible outside. (3) Periodic inspection ...

The sensor is a kind of detection device, which can feel the measured information, and can transform the felt information into electrical signals or other required forms of information output according to a certain law, so as to meet the requirements of information transmission, processing, storage, display, recording and control. Photoelectric sensors and ...

1. The wiring method of various sensors is basically the same, and the pressure sensor generally has a two-wire system, a three-wire system, a four-wire system, and some five-wire systems; 2. The two-wire system of the pressure sensor is relatively simple, one wire is connected to the positive pole of the power supply, and the other wire is the signal line through the instrument.

1. Ordinary metal straight tube package temperature sensor The packaging form of this temperature sensor is mostly used in a simple installation environment, and is divided into high temperature temperature sensor, medium temperature or ordinary temperature sensor and low temperature temperature sensor according to the measured temperature range.

How laser sensors work In the industrial field, the most common laser sensor is the laser displacement sensor, also known as the laser distance sensor, which can accurately measure the position, displacement and other changes of the measured object without contact, and is mainly used to detect the displacement, thickness, vibration, distance of the object.

1. There is no display on the digital display after connecting the power supply (1) Check whether the power cord is broken and whether the plug contact is good. (2) Whether the power fuse of the digital display meter is blown. (3) Whether the power supply voltage meets the requirements. 2. The digital display table does not count (1) Passing ...

Liquid level sensors A liquid level sensor is a common sensor that measures the position of a liquid level, and it is an output that converts the height of the level into an electrical signal. The liquid level sensor is a modular circuit, which has the advantages of acid resistance, moisture resistance, shock resistance, corrosion resistance, etc., and the circuit contains constant current feedback ...

1. Red LED – visible light, easy to adjust. 2. Infrared LED – high energy invisible light. 3. Red laser – visible light, its physical properties are ideal for small object detection and large detection ranges. ...

The progress of industrial automation and intellectualization has enabled human beings to gradually liberate themselves from heavy manual labor, and the emergence of machine tools and machining centers has enabled machines to complete the processing of parts faster and more accurately, and the emergence of automatic loading and unloading systems has made the machining center more powerful. And the loading and unloading ...

There are three basic components of a fiber optic sensor network, one of which is called a single-point sensor. An optical fiber only plays the role of transmission here, and the other is called a multi-point sensor, where an optical fiber strings many sensors together, so that many sensors can share a light source to achieve networking.

1. Resistive sensors The basic principle of a resistive sensor is to convert the measured change into a change in the resistance value of the sensing element, and then turn it into an electrical signal output through the conversion circuit. Applications: 1. Strain resistance sensor, used to measure tensile and compressive stress, and other physical quantities based on this...

(1) When the target to be measured is not perpendicular to the transducer of the sensor. This is because the target of the ultrasonic test must be within an angle of no more than 10° perpendicular to the sensor. (2) When a small beam diameter is required. Because the diameter of the general ultrasonic beam is ...

The photoelectric head of a photoelectric sensor is a precision device, and misalignment can seriously affect the measurement results. This usually happens when external forces interfere with it, such as when the sensor position is shifted due to excessive force during cable construction. At this point, the position of the photohead needs to be readjusted. How to adjust: ...

The first point is that photoelectric sensors and fiber optic sensors work differently First of all, from the working principle of the two, first of all, the photoelectric sensor works according to the principle of the photoelectric effect, that is, when the light hits the photoelectric sensor made of semiconductors, it will emit light ...