| project | content |
| Order product number | LS-501P |
| Model | LS-501P |
| Working status indicator | Orange LED (lights up at output 1 and output 2 ON) |
| Environmental resistance: Protective structure | IP40(IEC) |
| Environmental resistance: The ambient temperature at which it is used | -10~+55°C [-10~+50°C when 4~7 units are installed closely, -10~+45°C when 8~16 units are installed closely] (Note that condensation and freezing are not allowed), When storing: -20~+70°C |
| Environmental resistance: Ambient humidity is used | 35~85%RH, when storing: 35~85%RH |
| Environmental resistance: Withstand voltage | AC1,000V for 1 minute between all power connection terminals and housing |
| Environmental resistance: insulation resistance | 20MΩ or more, DC250V based on high impedance meter between all power supply terminals and housing |
| Environmental resistance: Vibration resistance | Frequency: 10~150Hz, Double amplitude: 0.75mm (max. 10G) 2 hours each in X, Y, and Z directions (no power) |
| Environmental resistance: impact resistance | Endurance: 98 m/s2 (approx. 10 G) 5 times in each direction of XYZ (no power-on) |
| Material | Body shell: Polycarbonate |
Hood: Polycarbonate |
Switch: Polyoxymethylene |
| cable | - |
| weight | Body weight: Approximately 15 g |
Package weight: about 55g |
| annex | FX-MB1 (amplifier protection seal): One set |
| Supply voltage | 12~24V DC +10-15% pulsation P-P10% or less |
| power consumption | Normal operation: 1,200 mW or less (50 mA or less current consumption at 24 V supply voltage) |
In ECO mode: 980 mW or less (40 mA or less current consumption at 24 V supply voltage) |
| Outputs (Output 1, Output 2) | PNP open-collector transistors |
・Maximum source current: 50mA (Note) |
・Applied voltage: 30V DC or less (between output and +V) |
・Residual voltage: 2 V or less (at maximum source current) |
Note: 25mA when more than 5 units are connected in series. However, this does not apply for extension cables. |
| Output (Output 1, Output 2): Output action | ON when the light is in/ON when the light is not in |
| Output (Output 1, Output 2): Short-circuit protection | Equipped with |
| Detection output setting: output 1 | Normal mode/differential mode/differential mode/window comparison mode |
| Detection output setting: Output 2 | Normal mode/differential mode/differential mode/self-diagnosis output mode switching |
| Reaction time | H-SP: 60 μs or less, FAST: 150 μs or less, STD: 250 μs or less, LONG: 500 μs or less, U-LG: 5 ms or less, HYPR: 24 ms or less Switchable type |
| Monitor the current output | - |
| External inputs | PNP contactless input |
・Signal conditions: High: +4V~+V DC (inflow current 3.0mA or less), Low: 0~+0.6V DC, or open |
・Input impedance: Approx. 10kΩ |
| External input function | Drop light stop/teach (fully automatic, limited, 2 points)/logic operation/copy function locking/display adjustment/database loading/database saving Switching |
| Laser flood light indicator | Colored LED (lights up when laser light is emitted) |
| Output selection indicator | Yellow LED (lights up when output is selected) |
| Digital display | Digital display Digital display 8-digit 7-segment (4-digit green LED + 4-digit red LED) mode display (yellow LED)  /D・CUST・PRO |
| The amount of light entering the display range | H-SP/FAST/STD:0～4,000 |
LONG/U-LG/HYPR:0～9,999 |
| How to set the sensitivity | 2-point teaching/limited teaching/automatic teaching/manual adjustment |
| Logical operations | Detect between output 1 and the operand: invalid /and/or/xor switching |
Object: Detection output 2 / Tight to the upper amplifier (detection output 1) / External input switching |
| Timer function | <输出1> |
Off delay timer / On delay timer / One-touch timer / On · Off delay timer / On delay timer · One-touch timer |
Active/Invalid Timer Time is variable |
<输出2> |
Disconnect Delay Timer / Turn On Delay Timer / One-Touch Timer Active/ |
Inactive switching timer time variable |
| Timer function: Timer time | Timer range "ms": Approx. 0.5 ms, approx. 1~9,999 ms, approx. 1 ms increments |
Timer range "sec": about 0.5s, about 1~32s, about 1s increments |
Timer range "1/10ms": Approx. 0.05ms, approx. 0.1~999.9ms, approx. 0.1ms Each output is set separately |
| Anti-jamming function | Equipped with |
Note: Number of units that can be installed closely: H-SP: 0 / FAST: 2 / STD, LONG, U-LG, HYPR: 4. |
| Cable extension | The total length of the cable over 0.3mm2 can be extended to 100m |
Contact
working hours
