| project | content |
| Order product number | FX-101P |
| Model | FX-101P |
| Supply voltage | 12~24V DC±10% pulsation P-P10% or less |
| Power consumption | Typical: 720 mW or less (24 V power supply voltage, 30 mA current consumption or less) |
ECO mode: 600 mW or less (24 V power supply voltage, 25 mA current consumption or less) |
| output | PNP open-collector transistors |
・Maximum source current: 100mA |
・Applied voltage: 30V DC or less (between output and +V) |
・Residual voltage: 1.5 V or less (at 100 mA source current) |
| Output: Outputs the action | You can switch ON when the light is in or ON when the light is not in the SET mode |
| Output: Short-circuit protection | Equipped with |
| External inputs | PNP contactless input |
・Signal conditions |
High:+4V~+V DC (Inflow current 0.5~3mA) |
Low: 0~+0.6V DC or off |
・Input impedance: Approx. 10kΩ |
| Reaction time | Projection frequency: 0:250μs or less (factory state) |
The projection frequency is 1:450μs or less |
Beam frequency 2: 500μs or less |
Projection frequency 3: 600μs or less |
| How to set the sensitivity | 2 points of teaching/limited teaching/automatic teaching |
| Working status indicator | Orange LED (lights up when ON is output) |
| Numeric value display | 4-digit (green) + 4-digit (red) LCD display |
| Set the sensitivity fine-tuning function | Equipped with |
| Timer function | The on/off delay timer can be adjusted to be active or inactive |
[Timer time: 1ms, 5ms, 10ms, 20ms, 40ms, 50ms, 100ms, 500ms, 1,000ms] |
| Adjustable amount of light emitted | 3 grades + automatic setting (from part produced in December, 2007) |
| Anti-jamming function | Equipped with adjustable active or inactive |
| Environmental resistance: The ambient temperature at which it is used | -10~+55°C (-10~+50°C when 4~7 units are installed closely, -10~+45°C when 8~16 units are installed closely) (note that condensation and freezing are not allowed), storage: -20~+70°C |
| Environmental resistance: Ambient humidity is used | 35~85%RH, when stored: 35~85%RH |
| Environmental resistance: Use ambient illumination | Incandescent lamp: 3,000 Rx or less on the light-receiving surface |
| Environmental resistance: Withstand voltage | AC1,000V for 1 minute between all power connection terminals and housing |
Note: The withstand voltage and insulation resistance values are only available for individual amplifier parts. |
| Environmental resistance: insulation resistance | A high-impedance meter based on 250 VDC between all power supply terminals and housings of 20 MΩ or more |
Note: The withstand voltage and insulation resistance values are only available for individual amplifier parts. |
| Environmental resistance: Vibration resistance | Frequency: 10~150Hz, double amplitude: 0.75mm, 2 hours each in the X, Y and Z directions |
| Environmental resistance: impact resistance | Acceleration: 98 m/s2 (approx. 10 G) 5 times each in the X, Y and Z directions |
| Projection Element (Modulated) | Red LED (Emission peak wavelength: 643nm) |
| Material | Enclosure cover: Polycarbonate |
Key switches: Polycarbonate |
Fiber Optic Lock Lever: PBT |
| Connection | Connector connectivity |
Note: Models without "-CC2" at the end of the model name do not come with a connector cable (CN-14A-C2). Be sure to use the separately sold cable with connector CN-14A(-R)-C□, connector CN-14A, or Japan crimp terminal manufacturer (contact: SPHD-001T-P0.5, housing: PAP-04V-S). |
| Wiring length | The total length of the cable of 0.3mm2 or more can be extended to 100m |
| weight | Body weight: Approximately 15 g |
Package weight: about 35g |
Contact
working hours
