Xinjie/XINJE inverter VH3 series 0.5KHz-16KHz

Introduction: XINJE/XINJE VH3 series inverter non-inductive vector control, which can smoothly drive large loads at low frequency; The output frequency is 500Hz, which can control high-speed motors. Using SMT full patch production and conformal coating treatment process, the product performance is stable.

Xinjie/XINJEVH3 series

peculiarity

Inductive vector control can smoothly drive large loads at low frequencies

The output frequency is 500Hz, which can control high-speed motors

Built-in two kinds of PID adjustment and simple PLC function, convenient for customers to use various needs

Rich and flexible input and output interfaces and control methods, strong versatility

Using SMT full patch production and conformal coating treatment process, the product performance is stable

Perfect protection function, good heat dissipation air duct design

Standard RJ45 network cable external interface (panel is connected to the main control board)

environment

Place of use: indoor, not exposed to direct sunlight, no dust, corrosive gas, oil mist, water vapor, etc

Altitude: less than 1000 meters (derating is required above 1000 meters)

Ambient temperature: -10°C-+40°C

Humidity: less than 90%RH, no condensation

Vibration: less than 5.9 m/s2 (0.6 M)

Storage temperature: -20 °C - +60 °C

structure

Protection structure: IP20 (in the case of optional status display unit or keypad)

Cooling method: forced air cooling

Installation: wall-mounted, cabinet installation

Basic functions

**High frequency: Vector control: 0 - 500Hz V/F control: 0 - 500Hz

Carrier frequency: 0.5KHz-16KHz can automatically adjust the carrier frequency according to the load characteristics

Frequency Resolution: Digital Setting: 0.01Hz; Analog Setting: **High Frequency ×0.025%

Control mode: open-loop vector control (SVC) V/F control

Starting torque: G type machine; 0.5HZ/150%(SVC) P-type machine; 0.5HZ/100%

Steady speed accuracy: ±0.5% (SVC)

Overload capacity: G type: 150% rated current 60s; 180% rated current for 3s. P type: 120% rated current 60s; 150% rated current for 3s.

Torque Lift: Automatic Torque Lifting; Manual torque increased by 0.1% - 30.0%

V/F curve: three ways: straight type: multi-point type: N-power V/F curve (1.2 power, 1.4 power, 1.6 power, 1.8 power, 2.0 power)

V/F separation: 2 ways: full separation, semi-separation

Acceleration and deceleration curve: straight line or S-curve acceleration and deceleration mode. Four kinds of acceleration and deceleration time, acceleration and deceleration time range 0.0-6500.0s

DC braking: DC braking frequency: 0.00HZ - ** large frequency Braking time: 0.0s - 36.0s Braking action current value: 0.0% - 100.0%

Jog control: jog frequency range: 0.00Hz-50.00Hz. The jog acceleration and deceleration time is 0.0s - 6500.0s.

Simple PLC, multi-speed operation: through the built-in PLC or control terminal to achieve ** more than 16 speed operation

Built-in PID: Enables easy implementation of closed-loop control systems for process control

Automatic Voltage Adjustment (AVR): Automatically keeps the output voltage constant when the grid voltage changes

Over-voltage and over-loss velocity control: The current and voltage are automatically limited during operation to prevent frequent over-current and over-voltage tripping

Fast current limiting function: **Minimize overcurrent faults and protect the normal operation of the inverter

Torque limitation and control: the "excavator" feature automatically limits the torque during operation to prevent frequent overcurrent tripping; Closed-loop vector mode enables torque control

Personalization features

Outstanding performance: Asynchronous motor control with high-performance current vector control technology

Instantaneous stop: In the event of an instantaneous power failure, the voltage is compensated by load feedback energy to maintain the inverter's continuous operation for a short time

Fast current limiting: Avoid frequent overcurrent faults in the inverter

Timing control: timing control function: set the time range 0.0Min - 6500.0Min

Multi-motor switching: two sets of motor parameters, which can realize the switching control of two motors

Multi-threaded bus support: Support two types of fieldbus: Modbus, X-NET bus control

Run the function

Command source: the operation panel is given, the control terminal is given, and the serial communication port is given. There are several ways to switch

Frequency source: 10 frequency sources: digital given, analog voltage given, analog current given, pulse given, serial port given. There are several ways to switch.

Auxiliary Frequency Sources: 10 auxiliary frequency sources. Auxiliary frequency trimming and frequency synthesis can be flexibly realized

Input terminals: 5 digital input terminals, of which 1 supports high-speed pulse input of 100kHz 2 analog input terminals, 1 only supports 0-10V voltage input 1 supports 0-10V voltage input

Output terminal: 1 high-speed pulse output terminal (optional open collector type), support 0-100KHz square wave signal output 1 digital output terminal 1 relay output terminal 1 analog output terminal, support 0-20mA current output or 0-10V voltage output

Operation: Overcurrent Protection; Overvoltage protection; Under-voltage protection; Overheat protection; overload protection, etc

Options: brake components; VH3 base; Operator panel extension cable

All suppliers of 76 Technology have been strictly audited to ensure that all sources of goods come from manufacturers or formal agents. Our self-confidence stems from our strict requirements for product quality, adhere to the original **, fake one pay ten, if there is a demand, welcome to consult the delivery date and price, we will select the best quotation for you in many channels, 76 technology multi-brand one-stop procurement, save you time, worry, money.

The above is Xinjie/XINJE inverter VH3 series 0.5KHz-16KHz products, the purpose of 76 technology is to survive by quality, develop by reputation, and eternity by service, give us a chance and give you a surprise.

Xinjie/XINJE inverter VH3 series 0.5KHz-16KHz

Sections viewed

Contact

working hours