CHINT/CHINT DTS634 three-phase electronic active energy meter

NB1G-63 miniature circuit breaker (hereinafter referred to as circuit breaker) is suitable for AC 50Hz, rated working voltage 230V, rated current to 63A in the line, the line plays the role of overload short circuit and overvoltage protection, can also be used as the line infrequent operation conversion. Standards: GB ...

The main function of the AX-X1 auxiliary contact: it can be assembled with the circuit breaker to realize the signal indication of the on/off of the long-distance circuit breaker. Conform to the standard: GB/T14048.5, IEC60947-5-1 Parameters and performance Action characteristics: The wiring principle of the auxiliary contact is shown in Figure 1. When the auxiliary contact is opened, the 17th and 12th terminals ...

The circuit breaker is rated for insulation voltage up to 800V, suitable for AC 50Hz, rated working voltage up to 400V, rated working current from 10A to 250A in the distribution network circuit, used to distribute power and protect lines and power supply equipment from overload, short circuit, undervoltage and other faults. At the same time ...

NB1L-40 □ residual current action circuit breaker is suitable for AC 50Hz, rated voltage single pole two wires, two poles 230V, three poles, three poles four wires, four poles 400V, rated current to 40A line, when the person is electrocuted or the leakage current of the power grid exceeds the specified value, the residual current action circuit breaker can be used in the pole ...

CJ40 series AC contactor (hereinafter referred to as contactor) is mainly used for switching and breaking circuits in power systems with AC 50Hz or 60Hz, rated voltage to 660V or 1140V, and current to 1000A.

The molded case circuit breaker provides protection for the lines and equipment when overload, short circuit and undervoltage occur in the lines and equipment in the distribution line, and can also provide overload, short circuit and undervoltage protection for the infrequent start of the motor. ● Shell Frame Grade NXM Series Molded Case Circuit Breaker: 63A, 125A, 160A ...

Rated working voltage (Ue): AC 230V, 50Hz; Overvoltage action setting value (Uo): 280(1±5%)V; Undervoltage action setting value: (35%-70%) Ue; Rated insulation voltage (Ui) : 500V; Trip characteristics: Tripper combined with NXB-63 series circuit breaker ...

CJ40 series AC contactor (hereinafter referred to as contactor) is mainly used for switching and breaking circuits in power systems with AC 50Hz or 60Hz, rated voltage to 660V or 1140V, and current to 1000A.

The S9 shunt trip device (hereinafter referred to as the tripper) is mainly used for matching with NB1 or NBH8 series circuit breakers, and is suitable for long-distance shunt tripping operation in lines with AC 50Hz (or 60Hz) rated voltage to 400V. Meets the standard: IEC60947-5-1, obtained CE certification. 3.1 Basic ...

NP2 series button is suitable for AC 50Hz or 60Hz, rated working voltage to 415V and DC working voltage to 250V in industrial control circuits, as electromagnetic starters, contactors, relays and other electrical circuit control, with indicator light button is also suitable for light signal indication ...

CHINT Xinrui NM5 series plastic case circuit breaker is suitable for AC 50/60Hz, rated voltage AC690V and below, rated current from 16A to 1000A circuits. As the rated current of on, breaking and bearing, it can be overloaded, short-circuited and under-voltage in the line and electrical equipment.

Introduction: CHINT/CHINT AC contactor NC3-09 (hereinafter referred to as contactor) is mainly used for AC 50Hz (or 60Hz), rated working voltage to 380V (NC3-09 - 16 can be up to 660V) rated working current to 170A power system to connect and break circuits, and with the appropriate ...

NCH8G series household AC contactor (hereinafter referred to as contactor) is mainly suitable for AC 50Hz (or 60Hz), rated working voltage to 400V rated working current to 63A circuit, control household appliances and similar uses of low-inductance and micro-inductance loads; It can also be used to control household ...

ND9 signal light is suitable for AC 50Hz/60Hz, rated voltage up to 230V, DC voltage up to 230V circuit control system. It is used as an indication signal, preset signal, accident signal and other indication of telecommunications, electrical and other lines. Standards: GB/T 14048.5, IEC 60947-5-1 ...

The TB series is suitable for connecting wires in circuits with AC 50Hz or 60Hz, rated voltage up to 600V and rated current up to 100A. This series of products is connected by screw crimping, and the wire end needs to be crimped before it can be connected to the terminal block. Screw mounting. Comply with the standard ...

The NXHB-125 disconnector complies with IEC60898 and GB10963 standards. It is suitable for AC 50Hz or 60Hz, rated voltage 250V and below residential single-phase lines, to protect the overload and short circuit of electrical lines. The product has high breaking capacity, small size and a width of only 18mm. Zero, fire ...

NXMF series circuit breakers are suitable for AC 50/60Hz, rated working voltage to 690V, rated working current from 10A to 630A in the distribution network circuit, used to distribute power and protect lines and power equipment from overload, short circuit, undervoltage and other faults. At the same time, it can also be used as an electric motor ...

32-bit high-performance CPU, compiled execution mode, scan cycle is 10 times faster than analytical type, and the basic instruction single-step running time is 0.05μs. Weight: 102 Power consumption: 1.5 Power supply: DC24V±20% Digital inputs: 8 This article introduces the CHINT/CHINT NSC1 series motion controller.

NM10 series plastic shell circuit breaker (hereinafter referred to as circuit breaker) is mainly suitable for infrequent operation of AC 50Hz, rated working voltage to 380V, rated current to 600A in the distribution network circuit, used to distribute electric energy and protect lines and power equipment from overload, short circuit, under...

YBLX-HL travel switch is mainly used in the control circuit of AC 50Hz or 60Hz, voltage 380V, DC voltage 220V, for the travel control of the moving mechanism, the transformation of the direction or speed of the movement, the automatic control of the machine tool, the limit action of the moving mechanism and the control of the stroke or program. Comply with the standard ...