IDEC/Izumi Safety Interlock HS1T Heavy Duty Locking HS1T-XD44ZM-G

The operating head detachment detection function is standard. The key is made of a high-security bullet lock. There are 16 key numbers to choose from. There is a rear unlock button type for emergency evacuation and other purposes, and it can be attached to the rear lock release button unit attached to the aluminum frame. Adopt a small negative ...

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

VA circuit, LOCK position key removal, key 501,5m cable, rear unlock button Mechanical Specifications: Product Category Safety Interlocks Key Removal Position Removed in the locked position Environmental indicators Degree of protection IP65 Installation and installation specifications Cable length: 5 meters We take the guest ...

3 position action of OFF ⇒ ON ⇒ OFF to avoid danger. Pressing ON ⇒ OFF is a direct open-circuit action function. By pressing OFF (position 3) ⇒ releasing OFF (position 1), there is no structure in the ON state. （IEC60204-1； 9.2.5.8 ...

Three new contact types have been added, and the opening and closing status of the door can be monitored by connecting the auxiliary contact to the PLC Key features: By connecting the signal of the auxiliary contact directly to the PLC, the operation of each HS7A-DMP non-contact safety switch can be monitored. Ideal for installation on protective doors where positioning is difficult. By adapting ...

3 position action of OFF ⇒ ON ⇒ OFF to avoid danger. There is no structure in the ON state between pressing OFF (position 3) ⇒ releasing OFF (position 1). (IEC60204-1:2005, 10.9 terms, IEC60947-5-8:2007, 7.1.9 terms),

During mechanical operation, the guards/keys are securely locked. Remove the key to unlock the safety gate, and keep the load circuit and auxiliary circuit open. Ideal for applications where the key needs to be taken into a hazardous location to avoid accidental start-up of the device. Key interlock type ...

Vertical operating unit with ø16 mounting holes for easy installation. 2-contact 3-position switch for small teach pendants. Key features: Ergonomic, 3-position action of OFF ⇒ ON ⇒ OFF for danger avoidance. Position 1 ⇒ 2, built-in snap-action switch with light ...

The resin-based actuator for HS5 series safety switches can be easily mounted to the hand-held enabling switch with the included two screws. Key features: The resin-based actuator for HS5 series safety switches can be easily ...

IDEC/Izumi HS6B Subminiature HS6B-11B01 Safety Interlock Switch 1NC1NO 1NC 1NO Contact, 1m Cable 30x15x78mm enclosure One-piece cables reduce wiring time IP67 (IEC60529) waterproof sealing (contact sealing; The enclosure allows for drainage) Open directly ...

VA circuit, unplug the key in the LOCK position, key 501,5m cable Mechanical Specifications: Product Category Safety Interlocks Key Removal Position Removed in the locked position Degree of protection IP65 Cable length: 5 meters Our customer-centric service concept: the pursuit of a full range of services ...

By connecting the signal of the auxiliary contact directly to the PLC, the operation of each HS7A-DMP non-contact safety switch can be monitored. Ideal for installation on protective doors where positioning is difficult. With the appropriate combination of dedicated safety relay modules, it is possible to correspond to safety category 4 and can be connected to up to 36 groups, protection, etc.

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.

The actuator is mounted on the guard, the safety switch is mounted on the mechanical body, and the mechanical locking guard is installed. When the inertial action of the machine stops, the electromagnetic coil excitation is unlocked by an electrical signal from the controller, etc., for greater safety. In the event of a power outage and maintenance, special tools can be used ...

During mechanical operation, the guards/keys are securely locked. Remove the key to unlock the safety gate, and keep the load circuit and auxiliary circuit open. Ideal for applications where the key needs to be taken into a hazardous location to avoid accidental start-up of the device. Key interlock type ...

4 contacts, 3NC door, 1NC lock, monitoring circuit, spring lock, rear unlock button Compact body: 35x40x127mm 1400N locking strength Gold-plated contacts for small loads The head direction can be rotated 8 different actuator entries are allowed Applicable standard: EN ISO1411 ...

The HS1B is a full-size interlock switch in a more rugged industrial die-cast aluminum housing. Options include red or green LED indicators, as well as two different circuit configurations. The HS2B comes with an optional red or green LED indicator and features the same ...

Ensure the safety of workers by operating the key and carrying the key into the hazardous area. (2019/1/31_Discontinued in some models) Key features: During mechanical operation, the guards/keys are securely locked. Remove the key to unlock the safety protection gate and protect it.

By connecting the signal of the auxiliary contact directly to the PLC, the operation of each HS7A-DMP non-contact safety switch can be monitored. Ideal for installation on protective doors where positioning is difficult. With the appropriate combination of dedicated safety relay modules, it is possible to correspond to safety category 4 and can be connected to up to 36 groups, protection, etc.

Low power consumption, built-in 6 contacts, and high level of 3000N locking strength. The actuator is common to the HS1E type (3000N locking strength). 6. Built-in contact type, the same size as the original HS1E type. The dimensions are 35mm× 104mm×129mm. It is possible to change the opening and closing state of the door and the lock separately.