The FX-501 digital fiber optic sensor is equipped with the Sensing Engine SENTRION

The FX-501 digital fiber optic sensor is equipped with the Sensing Engine SENTRION with a reflective iris with a maximum of 3000 light and a minimum of 1000 light intake.
Digital Fiber Optic Sensor FX-501

Specifications are detailed
project	content
Order product number	FX-501
Model	FX-501
Supply voltage	12~24V DC±10% pulsation P-P10% or less
Power consumption	Typical: 960 mW or less (40 mA or less for 24 V supply voltage)
Power consumption	ECO mode: 680 mW or less (24 V power supply voltage, 28 mA current consumption or less)
output	NPN open-collector transistors
	・Maximum inflow current: 100mA (Note 1)
	・Applied voltage: 30V DC or less (between output and 0V)
	・Residual voltage: 2 V or less (Note 2) (under the condition of maximum inflow current)
	Note 1: 50 mA for connector type with more than 5 connectors.
	Note 2: When using a 5-meter-long one-touch cable (sold separately).
Output: The number of output points	1 point
Output: Outputs the action	L/D mode can be used to switch between ON when light is in or ON when light is not in light
Output: Short-circuit protection	Equipped with
Reaction time	H-SP: 25μs or less
	FAST: 60μs or less
	STD: 250μs or less
	LONG: 2 ms or less
	U-LG: 4 ms or less
	HYPR: 24ms or less Switchable
External inputs	-
External Input (Switching Output 2)	-
External input correspondence function	-
How to set the sensitivity	2-point teaching/limited teaching/automatic teaching/manual adjustment
The amount of light entering the display range	H-SP/FAST/STD：0～4,000
	LONG：0～8,000
	U-LG/HYPR：0～9,999
Timer function	Disconnect Delay Timer / On Delay Timer / One-shot Timer / Turn On • Off Delay Timer / On Delay • One-shot Timer Active/Invalid Switching Timer The timer is variable
Timer function: Timer time	Timer range "ms": Approx. 0.5 ms, approx. 1~9,999 ms, approx. 1 ms increments
	Timer range "sec." : about 0.5s, about 1~32s, about 1s units
	Timer range "1/10ms": 0.05ms, 0.1~999.9ms, 0.1ms
	Each output is set separately
Adjustable amount of light emitted	Equipped with 3 levels (25~100% for each level) + automatic setting [1 level (25~100%) for H-SP]
Anti-jamming function	Equipped with (Note) Auto/Frequency Switching Type
	Note: As shown in the table below, when using the automatic interference prevention function, the number of fiber heads that can be attached to each other varies depending on the reaction time. When using the different frequency anti-interference function, the number of fiber heads can be installed close to each other, and the maximum number of installations is 3.
	・Number of optical fiber heads that can be installed (unit: set)
	Reaction time: IP-1
	H-SP：0
	FAST：2
	STD：4
	LONG：8
	U-LG：8
	HYPR ：12
Various settings	Difference setting, transfer setting, projection setting, display reversal setting, ECO setting, database loading and saving setting, copy setting, code setting, reset setting, logic operation setting, benchmark tracking cycle setting, etc
Protective structures	IP40(IEC)
Use ambient temperature	-10~+55°C [-10~+50°C when 4~7 units are close together, -10~+45°C when 8~16 units are close together] (note that condensation and freezing are not allowed), and when storage: -20~+70°C
Projection Element (Modulated)	Red LED (Emission peak wavelength: 643nm)
Material	Shell, cover: Polycarbonate (Note)
	Switch: Polyester elastomer
	Note: Specifications are changed according to Panasonic brand products.
cable	-
Cable extension	-
weight	Body weight: Approximately 15 g
weight	Package weight: about 70g
accessory	FX-MB1 (amplifier protection seal): One set

Digital Fiber Optic Sensor FX-501 Equipped with Sensing Engine SENTRION with reflective aperture, the maximum amount of light is 3000, and the minimum amount of light is 1000.

The FX-501 digital fiber optic sensor is equipped with the Sensing Engine SENTRION

Sections viewed

Contact

working hours